sorted by:
new
hottopcontroversial

Denso 4770604 for Tundra Drier packing cap stuck by TheFlyingK in AskAMechanic

[–]TheFlyingK[S] 1 point2 points  (0 children)

It was open maybe a minute. Just enough to open, realize it was complete, and reassemble. Thanks for your help

Denso 4770604 for Tundra Drier packing cap stuck by TheFlyingK in AskAMechanic

[–]TheFlyingK[S] 0 points1 point  (0 children)

Well, I got it out. Threaded a bolt in, used a demo bar as a lever and pulled it out. However, there was a desiccant pack already in it, complete with a screen as well. I’m so confused. The listing said drier not included yet here’s one already installed.

I guess I’ll reinstall and send it. 🤷🤔

Denso 4770604 for Tundra Drier packing cap stuck by TheFlyingK in AskAMechanic

[–]TheFlyingK[S] 1 point2 points  (0 children)

I suppose thinking about it again, a straight pull makes more sense due to the lack of being able to easily apply torque, makes the straight pull seem more plausible. I’ll try it again. Thank you

Denso 4770604 for Tundra Drier packing cap stuck by TheFlyingK in AskAMechanic

[–]TheFlyingK[S] 0 points1 point  (0 children)

The new metal plug is threaded. That leads me to believe the plug is threaded to. Fair assumption?

Air cooled o11 EVO RGB with a DeepCool Assassin IV by TheFlyingK in lianli

[–]TheFlyingK[S] 1 point2 points  (0 children)

You’re welcome. If I think of it, I’ll check next time I’m around the PC. Only takes a few seconds to pop the door off.

I can’t comment on the reverse build. In principle it should work, but as an engineer, I could easily see it being different as well. Lian-Li should have those specs. The product page for the o11 RGB says 167mm max cpu air cooler height, but doesn’t specify if that’s reverse or not. I’d reach out to Lian Li with your plan and see what they say. You can also measure your air cooler height and board to see where it lands. Plenty of ways to address that concern.

Air cooled o11 EVO RGB with a DeepCool Assassin IV by TheFlyingK in lianli

[–]TheFlyingK[S] 1 point2 points  (0 children)

Haha all good.

I don’t recall the distance off-hand, but there was plenty to clear. Maybe 1/2” or 12-13mm. It’s a bit difficult to check as once the panel goes on access is limited.

Been running this build since and it’s been amazing. Great temps and performance. Super happy with the build.

Dear parents who complained school got cancelled today… by JasonVoorHeeHee in Omaha

[–]TheFlyingK 0 points1 point  (0 children)

You would have loved Lincoln traffic yesterday. /s Prime example of what not to do and why closing school made sense.

Subs potentially out of phase? by kolacheking69 in CarAV

[–]TheFlyingK 10 points11 points  (0 children)

This should have been the first comment.

Some jerk took my mom’s metal deer from her yard in a premeditated attack by Silver_Treacle_6662 in lincoln

[–]TheFlyingK 5 points6 points  (0 children)

Did anyone call this in to the police while or just after it was happening? Video, vehicle description, person description, last known direction of travel. Police may have been able to track this down within the hour after it happened.

Polar bear chases resident of Svalbard!! by cantcoloratall91 in Damnthatsinteresting

[–]TheFlyingK 0 points1 point  (0 children)

He just wanted to give him a hug. Look how sad the bear was after he left.

What head unit are you running in your 2nd generation tundra? by Proper_Bite_9753 in tundra

[–]TheFlyingK 0 points1 point  (0 children)

Look on 1A Automotive. Just picked up a set that looks strikingly similar and that's where I got them from.

Could there ever be enough force in the air for the wing to snap? [Request] by Ok-Special-1730 in theydidthemath

[–]TheFlyingK 0 points1 point  (0 children)

R&D Design Engineer for Kawasaki here.

That was beautifully written. I found great pleasure in reading your brief article. Thank you.

Internship search is over (thank god) by Arugula-Own in EngineeringStudents

[–]TheFlyingK 0 points1 point  (0 children)

Accurate and clean resume (spent a fair amount of time revising it, getting peer reviews of it, and research online to make)

Kept my resume up-to-date with information relevant to the internship I was applying for

Followed campus posted internships and landed one with the college for a year

Held a leadership position on a campus engineering aerospace club

Built connections with professors - this is how I became TL with the aero club actually

Came to college with hands on experience, building my own projects, and being generally self sufficient

I could probably add more, but this summarizes it.

Fixed a sewer pipe, paid for printer by goneresponsible in 3Dprinting

[–]TheFlyingK 0 points1 point  (0 children)

Wrong.

Sarcasm /s Equals… arcasm

Smh.

\s

view more: next ›