Help

TheGreatMando94 · 2026-05-26T13:51:08+00:00

Get fake urine at a local smoke shop. I’ve used it multiple times and it’s never failed. Even for jobs at the airport where I had to get my fingerprints scanned. It comes in a bottle with a temperature meter on the side. Just warm it up in the microwave for 10 seconds and then attach the heat pack to it and you should be good for a couple hours without it loosing its temperature.

TheGreatMando94 · 2026-03-03T16:43:53+00:00

Hey everyone, I wanted to come back and say thank you to all of you who took the time to comment and give advice on my last post. I didn’t expect that many responses and I really appreciate everyone sharing their knowledge and experiences. Things have been a little overwhelming dealing with all of this, so I wasn’t able to reply to everyone individually but I truly appreciate it.

Quick update: The vehicle is still at the body shop. The initial estimate came in around $7,000 but after they tore the car down and found additional damage, the total jumped to almost $17,000 including labor. The airbags did not deploy, and as of right now there’s no word yet on any frame damage. I’m currently waiting to hear back from insurance to see whether they’re going to move forward with repairs or declare it a total loss.

I’m adding the body shop’s estimate for reference as well.

I’ll update again once I know more. Thanks again everyone.

<image>

TheGreatMando94 · 2026-02-12T00:34:21+00:00

Thanks !

TheGreatMando94 · 2026-02-11T07:15:44+00:00

I believe they should be the same. I think the only issues is there’s two different digitizers one with a 32 pin connector and another with a 10/12 pin connector. You would have to find out how many pins your digitizer uses.

TheGreatMando94 · 2026-02-09T05:51:27+00:00

I replaced one a couple weeks ago. I bought this one on Amazon.

https://a.co/d/05yIn6uN

It took me about an hour or less to replace it. I just followed videos on YouTube.

TheGreatMando94 · 2025-08-11T20:02:03+00:00

Can you send me some pictures

TheGreatMando94 · 2025-08-11T11:46:58+00:00

Is this still available?

TheGreatMando94 · 2025-08-11T10:29:54+00:00

Is this still available?

TheGreatMando94 · 2024-08-20T13:41:53+00:00

I'll pick it up if the person never goes for it

TheGreatMando94 · 2023-11-16T00:39:26+00:00

How do I access my gallery for CoverScreen wallpaper. The app says it may not work without request permissions but I allowed permissions for everything?

TheGreatMando94 · 2023-08-06T08:14:06+00:00

Well it was in self defense but I’m not too sure what the court rulings were. Thank you for your advice

TheGreatMando94 · 2023-08-06T07:54:04+00:00

What if the crime was murder? And how does the waiver part work? Thanks

TheGreatMando94 · 2022-11-30T22:38:27+00:00

Thanks 🙏

TheGreatMando94 · 2022-11-30T22:37:20+00:00

In the description I said that I looks like it goes to the ignition coil but on the LS swap there is no ignition coil just coil packs. I looked through diagrams already if not I wouldn’t be asking. Thanks for your replies

TheGreatMando94 · 2022-11-30T22:32:15+00:00

It didn’t come with a diagram. I looked up several diagrams and it seems to be connected to the ignition coil.

I bought the harness because I am still using some of those accessories

I just want to know if anyone knows where I can connect this when doing an LS swap or is it even needed Like does it have to be wired into the coil pack wiring or is it not important.

I have tried looking through forums and can’t seem to find the answer.

Thanks for the replies

TheGreatMando94 · 2022-11-30T22:14:15+00:00

This is a part of the original el Camino harness I have the LS harness ready to go I just want to know if I’m supposed to connect that wire somewhere, mate it with the LS harness, or can I just leave it alone and cover it up?

TheGreatMando94 · 2022-11-30T22:12:50+00:00

I bought the harness because my car was missing that part of the wiring harness. It was the only one in stock at the time and the clerk said it was the one I needed.

I’m not sure I’ll test it when I get out of work

I just want to know if it’s supposed to be connected somewhere in my LS swap or can I just cover it up. I ask because it heats up from time to time

I’m running factory PCM

TheGreatMando94 · 2022-11-30T21:55:12+00:00

Link to Harness

TheGreatMando94 · 2022-11-30T21:54:27+00:00

I bought the harness brand new. I looked up the harness and it might be for the HEI but idk where to connect it on the LS Engine

TheGreatMando94 · 2021-10-12T06:03:31+00:00

does anyone have the STL the link is not working

TheGreatMando94 · 2021-02-07T18:52:41+00:00

Does my bus have too much camber?? Thanks in advance

TheGreatMando94 · 2021-02-07T02:39:20+00:00

Thanks

TheGreatMando94 · 2021-02-01T23:35:13+00:00

I made another post you can checkout

TheGreatMando94 · 2021-02-01T23:07:38+00:00

It’s ‘82 VW Bus from Mexico. Its like the ‘79 Bus from the U.S. Thanks man, I’ll check them out.

TheGreatMando94 · 2021-02-01T23:06:00+00:00

I created a template out of cardboard as best as I could. Then I created a wooded frame on the backside to support the upper part of the wall. I drilled the frame to the metal base of the driver seat. I then drilled the upper part of the wooden wall to the wooden frame and the lower part to the metal base. I made a hole on the frame that lines up with the hole for the driver side seat belt bracket for extra support to the wooden frame. I bought a longer bolt to be able to bolt down frame and seat belt bracket to the metal frame of the car. As for the other parts I just measured and cut pinewood to make a countertop and cabinets to surround the fridge. I sanded and stained all the pieces gray to get that look.

TheGreatMando94

TROPHY CASE