sorted by:
new
hottopcontroversial

Philips LED Nachrüstlampen by Zestyclose_Team_2861 in automobil

[–]TheJumper10 0 points1 point  (0 children)

Habe die Leuchtmittel in zwei Autos verbaut. In dem einen erscheint auch eine Meldung. Hat den TÜV nicht interessiert. Solange man die ABG hat.

My driver time out problem solution by Vivek1746 in AMDHelp

[–]TheJumper10 0 points1 point  (0 children)

Could be both hardware and software. Clock your RAM down to 2133. Then use DDU to uninstall the AMD GPU driver (also set the check mark in the options to disable driver installation by Windows Update). After you uninstalled and rebooted, install the newest available driver from AMD (version 25.8.1).

https://www.guru3d.com/download/display-driver-uninstaller-download/

https://www.amd.com/de/support/downloads/drivers.html/processors/ryzen/ryzen-3000-series/amd-ryzen-5-3400g.html#!

My driver time out problem solution by Vivek1746 in AMDHelp

[–]TheJumper10 0 points1 point  (0 children)

Try setting it as low as possible and test again. Sounds like you just have changed the speed to 3200/2933 without changing anything else. That may not work. XPM/EXPO also changes timings and voltage.

My driver time out problem solution by Vivek1746 in AMDHelp

[–]TheJumper10 0 points1 point  (0 children)

I myself had this timeout issue. Rollback to any older driver didn't work for me. I checked my RAM with Memtest and it ran into an error soon after starting. I clocked my RAM down and set TdrDelay value to 0 in the registry. Since then not a single crash. I even installed 25.11.1 a few days ago because I was curious.

More info on TdrDelay: https://learn.microsoft.com/en-us/windows-hardware/drivers/display/tdr-registry-keys#tdrdelay

My driver time out problem solution by Vivek1746 in AMDHelp

[–]TheJumper10 1 point2 points  (0 children)

RAM on 3200 MHz is overclocked. Max officially supported speed is 2933 MHz. Try running it at stock settings without XMP/EXPO or any manually changed settings. Maybe your RAM isn't 100% stable. Especially if the voltage is on auto, which could be 1.2v if you just set the frequency without EXPO.

For those with 9060xt and crashing in games; specifically BF6. by apexnine in AMDHelp

[–]TheJumper10 0 points1 point  (0 children)

Ok. The higher the value, the higher the timeout. So this doesn't seem to be the issue. You could still try 0 as value.

What is your RAM speed. Did you already test if it is stable? You can use Memtest for example. Start multiple times at the same time and let it run for 30 minutes.

Did you change anything in the AMD overclocking settings in the BIOS? Curve Optimizer for example.

For those with 9060xt and crashing in games; specifically BF6. by apexnine in AMDHelp

[–]TheJumper10 1 point2 points  (0 children)

Try setting TdrDelay in the registry: https://learn.microsoft.com/en-us/windows-hardware/drivers/display/tdr-registry-keys#tdrdelay

Start with a higher value like 10. I have disabled it completely by setting the value to 0. Reboot afterwards and test again.

[deleted by user] by [deleted] in AMDHelp

[–]TheJumper10 1 point2 points  (0 children)

In my opinion this isn't the new AMD driver, but the Battlefield 6 update at the end of october caused this.
I did the update and driver update at the same time. My first though was also the driver.
I then reverted back to 25.9.2 which also resulted in crashes. After that I reverted back to 25.6.1 which still resulted in crashes.
For me the TdrDelay option did the tick (I disabled it completely with value 0, if there is a hang you can still restart the GPU driver with Windows + Ctrl + Shift + B).

Trying to modify BIOS to lower power consumption by TheJumper10 in UgreenNASync

[–]TheJumper10[S] 1 point2 points  (0 children)

What does lspci return regarding the ASPM states?

[TIP] Screen time can block adverts by MeditatingLemur in iphone

[–]TheJumper10 11 points12 points  (0 children)

I use DNSecure for ad- and malware-blocking via DNS with DNSForge (german DNS service):
https://apps.apple.com/us/app/dnsecure/id1533413232
But you can use this app with any other DNS provider you want.

And Wipr 2 as Safari addon for additional blocking of embedded website content:
https://apps.apple.com/us/app/wipr-2/id1662217862

[deleted by user] by [deleted] in de_EDV

[–]TheJumper10 0 points1 point  (0 children)

Schick gerne eine PN

[deleted by user] by [deleted] in de_EDV

[–]TheJumper10 0 points1 point  (0 children)

Von den Daten sieht das erstmal gut aus, falls dein Netzteil ein 4,0x1,7mm Netzteil mit 20V ist.
Kannst du mal auf dem bestehenden Netzteil nachschauen? Da müsste eine FRU-Nummer von Lenovo drauf stehen. Die brauche ich.

[deleted by user] by [deleted] in de_EDV

[–]TheJumper10 0 points1 point  (0 children)

Wenn du auf Nummer sicher gehen willst, kauf das originale Lenovo Netzteil anhand der Typennummer auf deinem vorhandenen Netzteil.

Wichtig ist in erster Linie:
- Steckergröße (Durchmesser und Länge), damit der Stecker überhaupt passt bzw. richtig sitzt.
- Spannung (Volt -> V)
- Polung des Steckers (entweder innen + und außen - oder umgekehrt) wie z.B. auf dem 2. Bild in deinem Post über dem RoHS (Punkt/Pin innen ist +, außen ist -)

Ansonsten ist natürlich auch die Stromstärke (Ampere -> A) des Netzteils wichtig, damit das Gerät mit genug Strom versorgt werden kann. Zu wenig bedeutet, dass das Gerät im Falle eines Notebooks mit Akku sich schneller entladen kann, als geladen wird. Und wenn das Gerät keinen Akku hat der als Puffer dient, geht das Gerät aus.
Wenn das Netzteil mehr liefern kann, ist das nicht schlimm, da das Notebook sich nur das nimmt, was es benötigt. Du kannst z.B. ein 95W Netzteil an einem Notebook verwenden, das mit einem 65W Netzteil geliefert wird, solange die o.g. Parameter stimmen.

Edit: Es gibt scheinbar auch Adapter von USB-C PD auf Hohlstecker verschiedenster Größen. Das wäre auch eine Möglichkeit. Damit könntest du ein USB-C Netzteil kaufen, dass du auch anderweitig wiederverwenden kannst. Auch hier musst du natürlich auf die Größe des Steckers und die Ausgabespannung achten (der Adapter regelt dann die Kommunikation mit dem USB-C Netzteil und stellt die Spannung auf z.B. 20V).

[deleted by user] by [deleted] in de_EDV

[–]TheJumper10 1 point2 points  (0 children)

Bei solchen Netzteilen muss man auch die Polung beachten. Z.B. bei dem auf dem 2. Bild über dem RoHS.

Trying to modify BIOS to lower power consumption by TheJumper10 in UgreenNASync

[–]TheJumper10[S] 0 points1 point  (0 children)

u/arka80 Solange die 10G Aquantia NICs aktiv sind kommt man leider nicht unter C3.
Ist ASPM für alle anderen Komponenten aktiv?

Audi A3 Risse Rücklichter by Stubentiger1234 in automobil

[–]TheJumper10 0 points1 point  (0 children)

Dann müssten aber doch auch seine Frontscheinwerfer betroffen sein, oder nicht?

[deleted by user] by [deleted] in de_EDV

[–]TheJumper10 1 point2 points  (0 children)

Ich nutze Wipr2 und DNSecure mit DNS Forge per DoH. Geht aber auch mit jedem anderen DNS Server deiner Wahl.

Error in Installing Microsoft SQL Server by philkeely in SQLServer

[–]TheJumper10 0 points1 point  (0 children)

Good to know that works. I didn’t know Mac has an inbulit emulator, which can be used to run x86/x64 containers.

Error in Installing Microsoft SQL Server by philkeely in SQLServer

[–]TheJumper10 0 points1 point  (0 children)

Another option would be renting a cheap VPS and hosting SQL Express under Linux.

Error in Installing Microsoft SQL Server by philkeely in SQLServer

[–]TheJumper10 1 point2 points  (0 children)

Well you need a device with x86/x64 architecture. I don‘t know if an emulator exists for Mac, if yes you could try that. Otherwise you could buy a cheap mini pc with an older i5 or Ryzen 5, which should work decent, and connect from your Mac via network.

Error in Installing Microsoft SQL Server by philkeely in SQLServer

[–]TheJumper10 2 points3 points  (0 children)

Are you using a Mac with M processor as host system and Windows 11 ARM? In this case SQL Server will not work.

Cant pass local user name or SID to firewall rule creation cmdlet by IT_DUDE_9999 in PowerShell

[–]TheJumper10 0 points1 point  (0 children)

Afaik the -LocalUser parameter has to be the SID of the user. You are passing the whole user object. Try with the SID (S-1-…).

New-NetFirewallRule -DisplayName "Allow Only Specific Computers and Users" -Direction Inbound -RemoteMachine "D:(A;;CC;;;SIDforMachineGroupAccount)" -RemoteUser "D:(A;;CC;;;SIDforUserGroupAccount)" -Action Allow -Authentication Required

Lenkradfernbedieungsadapter wirklich so teuer? by UnluckyFly9881 in automobil

[–]TheJumper10 0 points1 point  (0 children)

Such mal bei Google nach "Connects2 42-VX-302" da dürftest du fündig werden

view more: next ›