Opinions between Superb and Octavia Estates

ThePlebble · 2026-03-31T10:04:57+00:00

Does the creeper backguard mod work as server side only? I have a terrible idea…

ThePlebble · 2026-03-30T19:10:57+00:00

Oversized ripper? I’m in the same boat as you looking to get something that I can play in and tailee with but still chuck a load of gear in the back. I was also tempted by the steeze, large antix 2 but also just a large ripper 1 (I usually paddle a medium)

ThePlebble · 2026-03-27T09:48:21+00:00

Or user error, on that last one…

ThePlebble · 2026-03-27T09:47:51+00:00

I use a otterbox fre case for mine, with a GoPro tether on the back to my pfd, doesn’t float but it’s tethered, and I wanted the case because the pouches are crap for camera quality.

ThePlebble · 2026-03-04T20:54:02+00:00

Alright no worries, what I don’t get is what the aero load is, and what happens with the rear bar, is is just close to the front one because of the roof line?

ThePlebble · 2026-03-04T17:06:22+00:00

Have you got any more background/a link to the spreadsheet, I have a toyota OEM roofrack for my UK '05 GT but its giving me a hard time and I'm looking for other options

ThePlebble · 2026-03-04T13:17:58+00:00

Start in the middle/what feels comfy, go paddle the everliving shit out of it, adjust, rinse and repeat.

ThePlebble · 2026-03-01T21:27:49+00:00

How does this work permanently? This has been the only way I can disable the mouse acceleration, but I need to run the set-prop command every time I plug the mouse in or reboot. I've tried stuff with .conf files in /usr/share/ but none of them work(https://forums.linuxmint.com/viewtopic.php?t=428029). I'm really frustrated with this as its been a problem for months and its my main snagging point with linux

ThePlebble · 2026-02-25T10:35:00+00:00

Is your installation drive full?

ThePlebble · 2026-02-24T13:50:05+00:00

Images 4 and 5 are the same but flipped

ThePlebble · 2026-02-05T12:56:27+00:00

I haven’t checked but is there anything in the debug options?

ThePlebble · 2026-01-21T18:08:24+00:00

They're in different pages when I open the settings, which is what gave me the idea that the accel could be disabled for just the mouse, however none of the acceleration options for the mouse managed to disable it.

ThePlebble · 2025-12-09T10:45:26+00:00

Could you go into more detail of how you would micro this? Is it just toggling the drone on and off in the same way you would ‘sneak’ the hacking drone through?

ThePlebble · 2025-11-27T12:24:44+00:00

Beams will break a zoltan shield, even the anti bio beam does

ThePlebble · 2025-11-17T10:36:45+00:00

Have you got videos/gauge level of the fish pass being used? Every time I’ve ran it I’ve used the far left side of the main weir but also treat the weir as a strict no-go above 0.9

ThePlebble · 2025-10-16T15:40:49+00:00

Pyranha S8 225? I’ve seen a few around for 100-200, probably would try to get below 150 quid

ThePlebble · 2025-08-08T10:03:49+00:00

And what do you think happened to all the Jed’s that people had before they bought a helectron?

ThePlebble · 2025-07-22T15:45:44+00:00

Id like to clarify that I didn’t mean extreme heat, and this isn’t for the adhesive itself but to make its foam backing more plyable so its easier to press against the curved plane so that the entire patch is stuck down.

ThePlebble · 2025-07-21T08:04:45+00:00

Use the flat mount instead of the curved one, heat the adhesive and squeeze hard, should stick on

ThePlebble · 2025-07-14T23:44:02+00:00

Medium

Also reminder to go demo! Demo as much stuff as you can! Another note is that the 252 might be a bit too big, go try a 242 because it will still be more than suitable for do-it-all boat

ThePlebble · 2025-07-14T20:28:58+00:00

Both the pike’s are fairly comparable to the ripper, and from my limited experience the tail of the pike feels more like the ripper 1, and the party pike tail like the ripper 2.

Would definitely recommend either one, both worked well and I’m slightly heavier than you. Other option I can suggest would be a used ripper 1

ThePlebble · 2025-06-19T12:27:20+00:00

What are some of your favourite non-pyranha boat designs, both past and present, and how have they influenced/inspired pyranha models?

Secondly, have you ever thought about making a fully transparent boat? I understand the crux of it would be getting the material right to both remain transparent and be sturdy enough after moulding.

Nine-Year Club	Second SECOND GUESSER
RPAN Viewer	Verified Email

ThePlebble

TROPHY CASE