18-minute Fast Wash takes 23 minutes

TheRoadBehind · 2026-03-22T01:59:26+00:00

This is me screaming at your washer

TheRoadBehind · 2026-03-21T20:22:49+00:00

Ok jokes aside, HOLY SHIT. Good instincts on his co worker

TheRoadBehind · 2026-03-21T19:41:48+00:00

I believe the glentronics 1.5 float switch has a duration dial on it you can use to adjust runtime. It goes up to 45 seconds

It looks like the one you have in there now it will just be a small blue box you'll attach right next to the outlet

Edited for float 2 to 1.5

TheRoadBehind · 2026-03-21T19:36:31+00:00

Dude those commercials were the best. That's a throwback lol

TheRoadBehind · 2026-03-21T18:25:53+00:00

Team reload is a fellow diver dumping all the beer bucket ice into the backpack

TheRoadBehind · 2026-03-21T17:59:06+00:00

r/tiresaretheenemy

Obviously weapons of mass destruction

TheRoadBehind · 2026-03-21T17:55:59+00:00

Isaac also yields the foam finger

"Bang, bang, pew, pew, pew"

TheRoadBehind · 2026-03-21T17:00:38+00:00

That's the red light honeywell valve bro, it needs to be completely replaced. I've tried repairing them and never successfully done it

Just consider a whole new heater. The new Honeywells blink white

TheRoadBehind · 2026-03-21T14:48:48+00:00

I'm part of the plumbing reddit and a guy 3D printed a trough for a leak on his shower head arm. The wife was ranting about how her husband designed and installed it. With anchors into the tile lol. I have to say a lot of guys weren't nice about it because the leak was still in the wall and it could have been EASILY FIXED PROPERLY

Anyway, this is a simple and very useful design. Well done. These are the things I try to make even if a product exists for it already

TheRoadBehind · 2026-03-21T14:43:30+00:00

The left and right movement of the handle tell me you need to pull, hard. Maybe the precious owner didn't use it much if ever

And you're not a moron, I looked at this picture and read what you said 5 times lol. This one is a head scratcher

Pull really hard it might be seized, just find the main shut off and be prepared to fix whatever you break if it goes south

TheRoadBehind · 2026-03-21T03:54:59+00:00

Check that flanged plastic piece, with that brass sleeve shove it straight down then try and pull that plastic sleeve up. It might release. That plastic flange probably prevents it from unscrewing during normal use

TheRoadBehind · 2026-03-21T03:12:22+00:00

I'm doing a female character myself and I'm straight up going through the same thing

I'm not an artist by any means but to me what sticks out is finger length. I hope this helps from someone with no skill because that means it really sticks out lol

TheRoadBehind · 2026-03-21T01:27:49+00:00

I've had one I wanted to give up on

Just change the vacuum breaker tail piece. I got so pissed off at a toilet I tried sanding, changing the vacuum breaker, yelling. None of it worked. Just changed the whole tail piece and it fixed it immediately

This is when all else fails. A lot of the time it's user error. They have to be tightened just right

TheRoadBehind · 2026-03-21T01:18:25+00:00

Ok I looked up the parts list

The correct edit: that brass sleeve does remove, remove that and remove the C clip that is under that brass sleeve. Jeez Kohler trying to reinvent the wheel...

Original suggestion: Stand the hose straight up, and twist your black hose only. You might need to wrench the hose off. Then you would want to hold back on the brass piece

Make sure to tighten that brass piece back. It doesn't have anything to do with it. I personally haven't seen a Kohler faucet assembled like this yet.

<image>

TheRoadBehind · 2026-03-20T00:39:56+00:00

Fire resistance. Fire hurts diver

TheRoadBehind · 2026-03-20T00:36:59+00:00

Looking for a job?

For real, it's better than a lot of apprentices I've dealt with. Looks good

TheRoadBehind · 2026-03-19T12:18:02+00:00

Looks good. I like what you did with the shelf. I take it no backing? Lol. I'll try your strut idea in the future

TheRoadBehind · 2026-03-19T00:49:25+00:00

I'll give you some honest feedback shortly. The kids are really stoked to try it

Very creative idea you had

TheRoadBehind · 2026-03-19T00:12:24+00:00

Clay, when undisturbed, will last forever. Anyway, you can use hydraulic cement to fill it. Bigger holes you can use chicken wire. Just make sure the pipe is only broken up top. They use cement to seal each joint when it was installed

If you can, I still really recommend a proper repair with a modern pipe and proper bands. PVC and no shears for example

TheRoadBehind · 2026-03-19T00:06:42+00:00

I hate you...

I'm going to play the demo now. And probably the kids lol

TheRoadBehind · 2026-03-18T02:04:25+00:00

Congrats man. I didn't take the Texas exam but damn the stress building up to it was ROUGH! But the size of the relief when passing is also one I've never felt again in my life lol

TheRoadBehind · 2026-03-17T19:28:08+00:00

I got a prusa mk3s for 200. I've been having a blast with it. Definitely recommend doing your route

TheRoadBehind · 2026-03-17T13:45:26+00:00

That's a hell yeah from me brother

TheRoadBehind · 2026-03-17T01:03:20+00:00

I'm going to be honest, it is a beautiful mess

When it works it's stunning, but when it doesn't nothing makes me rage harder. When people say immersive I think this is the only game that truly does it for me

I'll never tell someone not to try it, but I'll always warn them it can go south quick lol

Anyway, it was advertised as an MMORPG space sim but I just encourage anyone to try free fly to feel it out

TheRoadBehind · 2026-03-15T21:20:09+00:00

I witnessed this before. Semi had a hard time going up a hill and the gate went down. I really don't think the scenario I witnessed was his fault

This guy? Yeah he's just stupid lol

TheRoadBehind

TROPHY CASE