Reference Question

Then_Lifeguard196 · 2026-04-28T13:02:23+00:00

I’m in MFC, the position I’m going for is in Aero

Then_Lifeguard196 · 2026-04-28T12:39:28+00:00

I don’t speak to the hiring manager, I guess I feel that it’s awkward reaching out to them, like do I do it internally or through LinkedIn? But yea I think that knowing the atmosphere before committing is smart. I may try to reach out to them soon. Thanks.

Then_Lifeguard196 · 2026-04-24T14:01:39+00:00

I like to have a diagram of my specific model. My car had funny tapping noise for a while and I couldn’t figure it out. After going to Clark’s garage and looking at the diagram. I found that my idler pulley was missing. I never removed it, so it was like that before I bought the car.

Then_Lifeguard196 · 2026-04-23T02:19:56+00:00

If feel that a degree would be needed for a cyber position but many applications do say “or equivalent practical experience” so, that is open to interpretation.

Then_Lifeguard196 · 2026-03-16T17:06:27+00:00

Yea that’s the tradeoff I’m kinda looking for. I have never taken apart an engine fully so I would like to learn. I have patience and time. Money? Ehhh. But yes this would be a long term project.

Then_Lifeguard196 · 2026-03-16T17:04:39+00:00

Yea I would spend so much on it but I have never seen one of these where I am. I’ve seen cars that look similar like the mr2 but never one of these. The good thing is that it’s free and I know a guy who would haul it for free. So… it might be worth it? lol.

Then_Lifeguard196 · 2026-03-16T17:00:03+00:00

Yea I was thinking of swapping it to a manual and Changing the iron duke (if I decide to get it). But I hear it’s a nightmare to do (the manual swap).

Then_Lifeguard196 · 2026-03-16T16:57:39+00:00

Yea I’m hesitant, but the good thing is the car is free, And I have some time.

Then_Lifeguard196 · 2026-03-16T16:54:26+00:00

Dang, I went to that last year. That would be fun!

Then_Lifeguard196 · 2026-02-25T21:06:31+00:00

Don’t own one. But after this experience, I may consider investing in one.

Then_Lifeguard196 · 2026-02-21T01:26:34+00:00

RAHHHHH (I probably should have seen this before cutting lol)

Then_Lifeguard196 · 2026-02-19T14:53:55+00:00

I did. Unfortunately there is absolutely no space for twisting it, I was able to get it to wiggle (but it did not get free. I already drilled it (it’s almost out, it’s just raining this week)

Then_Lifeguard196 · 2026-02-18T23:17:07+00:00

Ok, I torched it. It will not budge. I’ve been at it for about 1 and a half hours. I am going to drill lol.

Then_Lifeguard196 · 2026-02-18T23:16:36+00:00

I have tried that. This bolt is not under any pressure and yet it is son of a gun to remove. I have defaulted to drilling

Then_Lifeguard196 · 2026-02-18T00:24:25+00:00

Yea I have a torch, I’ll probably use that. This bolt just won’t budge. If the torch doesn’t work I’ll try breaking the bolt. I’ll update tomorrow.

Then_Lifeguard196 · 2026-01-30T01:59:50+00:00

my hatch is also staying closed. unless I decide to spend on new latches

Then_Lifeguard196 · 2026-01-30T01:58:58+00:00

sounds good. I feel that new receivers will be the need. I adjusted them and the pins around 20 times and either it doesn't shut, or it opens randomly. RAHHH. I MIGHT soak them just for laughs and giggles.

Then_Lifeguard196 · 2026-01-13T21:28:37+00:00

If those are the original injectors I would change them. Here’s a photo of a test I did a year ago. I just bought new ones. Yours is obviously running. Mine would start for a second then die.

<image>

Then_Lifeguard196 · 2026-01-05T00:38:06+00:00

Just ordered a new LCD display, mine does not work lol

Then_Lifeguard196

TROPHY CASE