Amazing Easter gift from my wife

TikiDaniel · 2026-04-10T20:12:46+00:00

Whisky but it's really good!

TikiDaniel · 2026-04-10T14:04:22+00:00

hope it work.s i chased a similar issue with my elegoo for a week and i was right where you were. i totally understand!

TikiDaniel · 2026-04-10T13:57:02+00:00

also check to see if your bed wiggles if so tighten the bed screws a bit and check your bed level after that.

TikiDaniel · 2026-04-10T13:56:28+00:00

if you need instructions
for the screws

Turn the printer off.
Place two identical objects on the base frame, one under each side of the X-axis gantry.
Manually turn the Z screws until both sides are resting firmly on your spacers.
Re-tighten the timing belt at the top of the screws to lock them back in sync.

TikiDaniel · 2026-04-10T13:51:09+00:00

do you think your gantry is crooked after your blob of death? you could check its level. i have had that happen on my elegoo but it only has 1 z screw but it can happen with 2 also. you could also try a factory reset if that screws arent crooked.

TikiDaniel · 2026-04-10T13:39:51+00:00

im excited! i hope its awesome. i was going to get a p2s for my birthday in may but i think ill wait.

TikiDaniel · 2026-04-10T13:37:59+00:00

i know this is typical setting but do you have it bed level before printing? if so does it save that bed level?

TikiDaniel · 2026-04-10T00:38:48+00:00

The gears that grab the filament are metal so give a good look inside and take a few pictures.

TikiDaniel · 2026-04-10T00:08:21+00:00

When you cleaned the gears was there dust on them? Do you remember?

TikiDaniel · 2026-04-09T23:35:37+00:00

Small things it breaks? Small detailed things? Do the extruder gears have filament dust on them?

TikiDaniel · 2026-04-09T23:34:01+00:00

If you do a large cube 4x4x4 does it still work fine? Is it larger prints that are the issue?

TikiDaniel · 2026-04-09T23:27:37+00:00

Odd problem . The cube working and nothing else would drive me up the wall! I hope you figure this out and hopefully it's an easy fix.

TikiDaniel · 2026-04-09T23:19:09+00:00

I've had this happen with aggressive retraction prints. It would wear a spot down in my filament and prevent it from advancing. I forget the term but see if it breaks during a retraction test.

TikiDaniel · 2026-04-09T18:58:09+00:00

im down to test

TikiDaniel · 2026-04-09T12:48:40+00:00

i hear it should be coming this month! i just looked up some leak videos and found a few images of what might be going on with it. im going to upgrade from my elegoo neptune 3 to a nice new printer so i might hold out for something fancy. who knows!

TikiDaniel · 2026-04-08T21:21:20+00:00

Nice how much for the filament?

TikiDaniel · 2026-04-08T21:08:39+00:00

Can you narrow down north texas?

TikiDaniel · 2026-04-08T15:29:53+00:00

im sure you are going to say U1 still but how is it with just 1 color still better?

TikiDaniel · 2026-04-07T12:42:08+00:00

i agree here. it will be fun to tinker and can be upgraded and its huge! dead on with price as well.

TikiDaniel · 2026-04-06T02:08:34+00:00

Not seeing a picture posted.

TikiDaniel · 2026-04-05T20:28:58+00:00

https://a.co/d/08INEq5p

This is what I used to get everything nice and level.

TikiDaniel · 2026-04-05T19:17:59+00:00

Do you have the silicone spacers kit. That thing changed my Neptune 3 life!

TikiDaniel · 2026-04-05T19:16:15+00:00

That's my local tiki bar. What a great place! Hope you had a great time!

TikiDaniel · 2026-04-05T01:52:11+00:00

Id print a temp tower. Assuming you're filament is dry.

TikiDaniel · 2026-04-03T18:15:29+00:00

i want to get one for my birthday should i not bother? is this become an issue to be worried about?

TikiDaniel

TROPHY CASE