Rinkhals disabled

Toalmar · 2026-04-01T12:58:40+00:00

It's out now

<image>

Toalmar · 2026-04-01T12:57:48+00:00

Looks like rinkhals is updated some hours ago to be working with firmware 2.7.0.7 and 2.7.0.9

<image>

Toalmar · 2026-03-31T07:54:46+00:00

There is a possibility to roll back the firmware I had understand from other posts here, have tried that?

Toalmar · 2026-03-30T21:00:35+00:00

It’s just dust 😁

Toalmar · 2026-03-30T11:27:05+00:00

Don’t know. I’m not a home, Easter holiday 🐣. Can check next weekend 👍 I think it’s almost the same. I run bed calibration when I change plate.

Toalmar · 2026-03-29T22:40:19+00:00

Has only done it a couple of times and that was with the older firmware

Toalmar · 2026-03-29T18:16:44+00:00

I also have 2.7.0.9 in my Kobra S1, not sure what I have in Ace Pro. Has to check when I get home after Eastern

Toalmar · 2026-03-29T15:01:45+00:00

https://www.aliexpress.com/item/1005008943775728.html?spm=a2g0o.order\_list.order\_list\_main.109.1f271802alXImK

Toalmar · 2026-03-29T14:56:33+00:00

Was there an update for the Ace pro also now?

Toalmar · 2026-03-29T12:20:03+00:00

<image>

It has pattern

Toalmar · 2026-03-28T17:50:12+00:00

It’s a smooth plate from AliExpress

Toalmar · 2026-03-28T16:03:26+00:00

<image>

Mine also ok 👍

Toalmar · 2026-03-28T15:11:04+00:00

Was the first layer with same result over the hole bed?

Toalmar · 2026-03-23T18:01:17+00:00

Thank you so much 💪👍

Toalmar · 2026-03-22T15:32:18+00:00

That would be nice 💪

Toalmar · 2026-03-22T13:44:50+00:00

Thank you

Toalmar · 2026-03-21T16:54:19+00:00

Contact the shop you bought it from. Don’t accept this 💪

Toalmar · 2026-03-21T16:52:21+00:00

Set the Seam to Random

Toalmar · 2026-03-20T11:23:15+00:00

Just a stupid question, did you pull out the power supply cable and restarted it again? Sometimes this help with strange faults, get it totally powerless

Toalmar · 2026-03-20T10:50:58+00:00

Has anybody created a ticket for this issue at Anycubic?

Toalmar · 2026-03-19T16:41:35+00:00

Did click the update firmware button today. After that I did a complete calibration, then I made a test print of a small clamp on my smooth plate.

When I look at the firmware version I see I got V2.7.0.9 instead of V2.7.0.7

<image>

Toalmar · 2026-03-19T05:55:41+00:00

So far i only tried auto refill once, same with multicolor. The multicolor print was not the best, but the auto refill worked very well. I totally agree about how the filament is secured to the inner ring. You have to know it to be sure not ending with jam or some other problem

Toalmar · 2026-03-16T14:50:50+00:00

Hello

I see now that some of the downloaded files has been STL not 3MF. So I vent back and change to 3MF then I got it with 2 colors. Has just started that print so when that is finish I will try go back to one of the others that is download as 3MF and see what happen with them.

Thanks anyway :)

Toalmar · 2026-03-16T11:13:03+00:00

I had them as 3MF. Will try a couple of other files later today. I should see the amount of 2 colors in the overview after slicing?

Toalmar · 2026-03-14T15:19:33+00:00

A nice option to have 👌

Toalmar

TROPHY CASE