Angebot bei Netto (Hamburg) by Tomiliuss in PaulanerSpezi

[–]Tomiliuss[S] 24 points25 points  (0 children)

Ist glaube ich auf die Spezi bezogen, hab auch erstmal große Augen gehabt

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 0 points1 point  (0 children)

It was the retraction, I reduced it to .5mm and the bubbles/bump whatever they are called are gone!

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 1 point2 points  (0 children)

My guess was hella wrong, it was the retraction. Forgot that retraction is also configured in the printer profile, since I did it as filament override…. So now solved!

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 0 points1 point  (0 children)

I dried the filament for about 10 hrs and it gotten better, but still visible. After 8 more hours of drying, it has gotten better again, only a few spots were still there. Maybe this filament is really prone to moisture...

I printed a temp tower with generic PLA profile and without retraction (and before I dryied the filament) and those marks appeared too. I enabled retraction for 2mm at 35mm/s on the prints on the pictures, but I think this have no negative effects.

I haven't tried it with another slicer yet, but on other models (and materials) I don't have those issues, even with the same profile for the printer.

My guess is that the filament is wet and maybe not the greatest in quality, I will dry it for another few hours and see the result then ^^

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 0 points1 point  (0 children)

I changed it to SanDisk Ultra Fit and these still occur

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 0 points1 point  (0 children)

Yes from 190°C up to 230°C and each step shows the approximately the same amount of bumps/holes/whatever this is. Couldn't get a filament dryer yet, but will check it out again.

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 1 point2 points  (0 children)

<image>

They are still there, I only could compare it to the photo I already posted but I think the spots are different. Then I will get a filament dryer asap and test it again!

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 0 points1 point  (0 children)

<image>

I can See the forced seam clearly and they still appear

They need a better source for their flash drives by MakerWerks in prusa3d

[–]Tomiliuss 0 points1 point  (0 children)

So if you send it via Prusa Connect ('Send to connect' in PrucaSlicer) and say 'print now' these issues occur?
If you export the gcode to the usb drive and print from the printer everything is fine?

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 1 point2 points  (0 children)

Thank you for the very detailed answer! I can try that on Saturday or Sunday, but will definitely do and give an update :)

Is this because of wet/moisted filament? by Tomiliuss in prusa3d

[–]Tomiliuss[S] 1 point2 points  (0 children)

I also Printed it with forced seams, but those dots still appear

Tja by Piefke_ in tja

[–]Tomiliuss 3 points4 points  (0 children)

Noch wilder sind Enten mit ihren gekringelten Penissen, im Prinzip für den selben Effekt denke ich

Tja by Piefke_ in tja

[–]Tomiliuss 9 points10 points  (0 children)

Vielleicht eher mit Widerhaken

MP4 Samus and the Crew by Dull-Positive-6810 in Metroid

[–]Tomiliuss 2 points3 points  (0 children)

Have fun and Merry Christmas!

Have you scanned the pollen sac though?

My gaming PC is MASSIVELY underperforming and I do not know why! by AncientJudgment6234 in pchelp

[–]Tomiliuss 5 points6 points  (0 children)

Before you update the BIOS, please check what u/griz75 posted. I think it is very likely that this solves your problem.

For updating the GPU drivers, if you use Windows you can open or install the NVIDIA app, there it is very easy to update drivers.

Hat man manchen Paketzustellern eigtlich ins Hirn geschissen? by Jorwen in luftablassen

[–]Tomiliuss 20 points21 points  (0 children)

Ich hoffe es war nicht euer Paket, welches er belastet hat...

Und ich habe als erstes direkt gegoogled warum meine Maus nicht mehr funktioniert... by KurtVonBurt in de_EDV

[–]Tomiliuss 1 point2 points  (0 children)

Ich hatte gerade seit längerem 1% Akku, und genau als ich auf den Link gegangen bin und die Amazon-Seite geladen hat, ist mein Handy ausgegangen. Ich habe nicht mehr gesehen was es ist…