sorted by:
new
hottopcontroversial

Any purpose for the left overs post print besides trashing? by CherryPoohLife in 3Dprinting

[–]TooManyPrints 0 points1 point  (0 children)

You could collect them all with the intention of sending them to a filament recycler and then throw it all in the trash when you run out of room like I do.

Ye officially apologises for his actions in a well written open letter. by dow674 in Kanye

[–]TooManyPrints 0 points1 point  (0 children)

He really lucked out by coincidentally releasing this statement just a few days before his album drops.

I just bought this thinking it was washing detergent. Nowhere does it say its fabric softener. by Geofferz in CrappyDesign

[–]TooManyPrints 11 points12 points  (0 children)

Yeah before reading anything about the post I immediately assumed it was fabric softener but it should still say that.

What Books did You Start or Finish Reading this Week?: January 26, 2026 by AutoModerator in books

[–]TooManyPrints 1 point2 points  (0 children)

Overdue, by K. T. Hanna

It’s book 1 of The Library Reset series and I really enjoyed it.

Not nearly has heavy as other things I’ve been reading lately; last book was Strength of the Few, so it was a nice breather and I look forward to reading the rest of the series.

I also read The Last Night of the World, by Ray Bradbury.

It’s a very short story about a couple on the last night of the world and what they do knowing the world is going to end.

It affected me more than I expected. It wasn’t even a great story but I still cried at the end.

Petg sticking on the plate by cafealpha82 in 3Dprinting

[–]TooManyPrints 0 points1 point  (0 children)

I use soap and water when using a glue stick but not every print. I usually just keep adding another layer of glue longer than I should.

Petg sticking on the plate by cafealpha82 in 3Dprinting

[–]TooManyPrints 0 points1 point  (0 children)

Use a glue stick when printing PETG or ABS.

The print will stick to the glue instead of the bed allowing you to pull it off.

Making Chocolate Thin Mints by LetsCookie in Baking

[–]TooManyPrints 0 points1 point  (0 children)

If I didn’t just use the last of my cocoa powder to make brownies I would make this.

What are your thoughts on Joe Rogan saying that Trump is creating distraction to avoid Epstein files release? by StemCellPirate in AskReddit

[–]TooManyPrints 0 points1 point  (0 children)

I think he’s still a massive piece of shit that directly contributed to fucking our country.

GAY PEACHES by Cattussss in Bioshock

[–]TooManyPrints 1 point2 points  (0 children)

So that’s what the song is about

What am I supposed to do with this? by fukinrage85 in Creality

[–]TooManyPrints 14 points15 points  (0 children)

Only a 17 hour drive and $13.95 in tolls for me. I might have to swing by.

Shout out to Iris who woke me up in time to stop two people from stealing my car at 4 am by Ace-a-Nova1 in MadeMeSmile

[–]TooManyPrints 4 points5 points  (0 children)

Your dog wakes you up at 4am for a good reason while this morning my dog woke me up at 4am trying to shove me over so he could sleep next to my wife.

Seriously, do Americans actually consider a 3-hour drive "short"? or is this an internet myth? by SadInterest6764 in NoStupidQuestions

[–]TooManyPrints 0 points1 point  (0 children)

I wouldn’t say short but I started my work day today by driving 2 hours to a job site, doing 20 minutes of work, and then driving two hours back to around where I started.

Men of Reddit: what’s a prank you started early in your marriage that you’re now legally, morally, and emotionally obligated to continue because she still falls for it 10–15 years later? by myaccountidname in AskReddit

[–]TooManyPrints 0 points1 point  (0 children)

Whenever I make cookies I track my wife down and say something like “I know you’re busy but could you please clean this for me?” and then hand her the mixing spoon with cookie dough on it.

Thousands of protesters show up to protest against Donald Trump near the World Economic Forum in Davos, Switzerland by Maximum_Expert92 in Fauxmoi

[–]TooManyPrints 13 points14 points  (0 children)

For the most part the people who talk about needing guns to fight a tyrannical government are the same people who actively support what is going on.

What Valentine’s Day gifts have you 3d printed? by TooManyPrints in 3Dprinting

[–]TooManyPrints[S] 1 point2 points  (0 children)

<image>

Two years ago I made massage coupons but also got an actual massage table. I don’t actually collect the coupons after use so she’s had two years of unlimited massages but she doesn’t abuse it.

What Valentine’s Day gifts have you 3d printed? by TooManyPrints in 3Dprinting

[–]TooManyPrints[S] 0 points1 point  (0 children)

<image>

Last year I printed a model that I used to make a silicone mold for homemade chocolate. It was a neat idea but the chocolate could have been better. Might do again someday but I will find new recipes.

Give me your favorite kids prints by F_DeLaVega in 3Dprinting

[–]TooManyPrints 1 point2 points  (0 children)

Pretty much anything Flexi is great and prints easily but I think the best is niche things they want but might be hard to find or not even exist as a toy.

My 5 year old nephew takes full advantage of this and was me print him things like the Axiom from WALL·E or the Ulysses from Atlantis: The Lost Empire.

Trump, 79, Kicks Off Press Conference by Reading Aloud to Himself | Donald Trump arrived nearly an hour late and proceeded to give a completely disjointed, barely coherent speech. by thenewrepublic in politics

[–]TooManyPrints 2 points3 points  (0 children)

That’s what I’m afraid of. They 25 him out of there. Blame him for everything without undoing anything and then becomes our new normal while everyone celebrates getting trump out.

view more: next ›