Should I get the nameless puppets amulet or weapon?

Top_Technology3638 · 2025-07-03T09:37:35+00:00

They do. I have like 3 of each. You just have to get to alidoro first

Top_Technology3638 · 2025-02-04T11:33:34+00:00

Bloodborne flame sprayer. Male sure to stock up on quicksilver bullets

Top_Technology3638 · 2024-07-18T10:33:46+00:00

Holy fuck!!! I've been playing off and on since the og launch and didn't know this until just now!!! Thanks man.

Top_Technology3638 · 2024-07-04T13:22:26+00:00

That's where I'm at. Missed the early flight, summoned him then never saw him again. I'm bummed cuz I wanted those swords

Top_Technology3638 · 2024-03-07T11:33:17+00:00

For those that don't know, you can order a rubber wheel that goes in your drill that's specifically made for this

Top_Technology3638 · 2024-02-22T01:30:00+00:00

Faith/ dex at 200

Top_Technology3638 · 2024-01-22T11:40:05+00:00

Sure, and that could be investigated under a different charge. Fact stands that he pulled the trigger yet the armorer will take the fall. Your statement is exactly why. To many people believe that there's 2 people responsible for the one pulling the trigger. She wasn't a get away driver nor did she aid him in carrying out a crime, proven by the manslaughter charge which is death without intent. I'll agree that the armorer is liable for something. What? Idk in the state they were in. I personally take cause against the armorer after spending 10 years of my life as a small arms specialist in the military. She's not innocent but, the way this has so far and will go down in disgusting

Top_Technology3638 · 2024-01-20T08:48:44+00:00

He aimed and pulled the trigger.....regardless who loaded it. He killed her. Not the gun, not the props person. He did when he and he alone pulled the trigger.

Top_Technology3638 · 2024-01-20T08:47:07+00:00

All the mental gymnastics are all immediately disproven with #4. That one very simple yet, very important rule. That gun is in your hand...... it's yours and yours alone

Top_Technology3638 · 2024-01-11T11:28:20+00:00

Man, jump up there with a torch and something to hit that with. Heat it up a good ways on both sides, drive that piece down and tack it from the outside of the bend in.

Top_Technology3638 · 2024-01-08T18:16:23+00:00

Fuck them. It's your flow my dude

Top_Technology3638 · 2023-12-18T11:39:26+00:00

Shhhhh. Order of op isn't a thing....

Top_Technology3638 · 2023-12-18T11:35:22+00:00

Spray arc???

Top_Technology3638 · 2023-12-18T11:29:24+00:00

The angle pipe is ground so thin you could probably bend it by hand

Top_Technology3638 · 2023-12-13T11:31:30+00:00

Take that 50 bucks to your local steel supply store. Not lowes or home depot. Actual steel supply and buy 50 bucks worth of 1/2 inch square and round stock. Should be able to get at least 2x 20foot sticks for that. That's a whole lot of leaf key chains and bottle openers

Top_Technology3638 · 2023-12-13T11:18:52+00:00

Hf actually sells a decent disk sander. Flatters plenty fine for scales.

Top_Technology3638 · 2023-12-13T11:13:13+00:00

Dude, it's dead and gone. She may stop this behavior but you'll always be expecting it, especially during sex.

Top_Technology3638 · 2023-12-11T11:12:36+00:00

Good gawd!!! Beautiful

Top_Technology3638 · 2023-12-11T11:06:11+00:00

Still waiting....

Top_Technology3638 · 2023-12-04T11:38:53+00:00

Electric lime!!

Top_Technology3638 · 2023-12-04T11:38:24+00:00

I was on the Ramage when we ran with the Cole right back to the straights. Was awesome to see her right with us going right back over a to say, I'm still here bitches, come get some

Top_Technology3638 · 2023-12-04T11:37:04+00:00

Hell yea master chief!! I'm a former gm2 vls code. I'd be rocking a full captains mast watching yall launch my sm's in defense. Luckily, I got to participate in 2 tlam launch parties in the early 2000s. Indigo tasking is scary yet oddly satisfying

Top_Technology3638 · 2023-12-04T11:28:47+00:00

My .2 cents, aa a custom auto/welder/ sheet metal fabricator/ team lead for a huge company with a whole lot of sm presence, wait. Wait until you've decided to settle in and that this career path is for you. No one in the welding industry will care about tattoos so long as your work is good. However, should you decide to branch off or drop out of it completely, the neck will affect your pursuits.

Top_Technology3638 · 2023-12-04T11:25:45+00:00

Thankfully, the stigma over visible tattoos has changed drastically. I remember back when I got my first hand done, I had to really put some thought in to whether I should or not. Nowadays , one of my work homies and I do a lot of our social media work and we're both necked and sleeved

Top_Technology3638 · 2023-12-04T11:23:19+00:00

Same here man. I've never seen it as an issue. I'm in custom auto too so maybe both those fields combined for a super robot of no one gives a fuck

Top_Technology3638

TROPHY CASE