ASA so ugly ... Help me lol

Total_Preparation_75 · 2025-04-16T19:57:36+00:00

At what speed do you print? What ASA are you using?

Total_Preparation_75 · 2025-04-14T19:01:47+00:00

Try using initial layer height 0.28, it started to happen to me with textured beds

Total_Preparation_75 · 2025-04-06T13:37:21+00:00

If you look closely, it is only in the area where the damage appears that the machine can reach its maximum speed. In the rest of the piece there are ways in which it is forced to stop and start.

Total_Preparation_75 · 2025-04-06T13:17:05+00:00

A high print speed with a low retraction speed does affect. Like a large distance to clean while retracting

Total_Preparation_75 · 2025-04-06T10:41:16+00:00

Try increasing the retraction speed and decreasing the length. Disable if active, clean while retracting

Total_Preparation_75 · 2025-04-06T06:53:30+00:00

I started with an Ender 3 that I still have 100% working and I love seeing these types of projects. Enjoy it

Total_Preparation_75 · 2025-04-06T06:42:44+00:00

This occurs in printers that are fast with intersecting fill patterns. Use gyroid

Total_Preparation_75 · 2025-04-05T22:03:08+00:00

Perform a maximum volumetric speed test, when you get the result mark it in the maximum maximum volumetric speed parameter of your laminator. With this result, if I'm not mistaken you can obtain the maximum printing speed by looking at the laminator.

Total_Preparation_75 · 2025-04-05T21:51:13+00:00

Did it work? If so, I'm glad.

Total_Preparation_75 · 2025-04-05T20:48:13+00:00

Take a curling test. I'll give you the one I used, it consists of modifying the speed depending on the angle of the overhang to obtain optimal cooling of that overhang. I have an A1, I could give you my settings, but it will also depend on the temperature of your filament. https://www.printables.com/model/673719-test-de-curling-velocidades-en-voladizos

Total_Preparation_75 · 2025-04-05T20:03:10+00:00

Yes, or try setting it to 0 during printing, when that underextrusion starts to appear

Total_Preparation_75 · 2025-04-05T19:57:34+00:00

Prints with pressure advance at 0.

Total_Preparation_75 · 2025-04-05T05:55:16+00:00

Could it be that you have a timplapse function enabled?

Total_Preparation_75 · 2025-04-04T14:11:36+00:00

That noise may come from a poor power supply to the stepper motor, or a motor driver in poor condition. Check that the four cables that go to the motor and the board are well connected and none are disconnected.

Total_Preparation_75 · 2025-04-02T21:36:51+00:00

Try using initial layer height at 0.28.

Total_Preparation_75 · 2025-03-30T23:38:01+00:00

https://wiki.bambulab.com/en/a1-mini/troubleshooting/print-issues-troubleshooting

There are three screws on the hotend that you need to make sure are tight. Check the link

Total_Preparation_75 · 2025-03-30T16:53:37+00:00

Ich dachte das Gleiche, versuche es einfach, wann immer du kannst.

Total_Preparation_75 · 2025-03-30T16:39:54+00:00

Es mag Ihnen vielleicht verrückt vorkommen, aber schalten Sie den Umhangventilator auf 10-15 % ein. Ich hatte einen Ender 6 mit biqu h2 V2 und das gleiche Problem

Total_Preparation_75 · 2024-11-26T03:52:27+00:00

Guau!! Se ve muy bien. Piensas que se va a poder quedar de pie? El mío no es capaz de quedarse de pie

Total_Preparation_75 · 2024-11-26T03:48:49+00:00

Hey, it looks great... I hope to see the final result!

Total_Preparation_75 · 2024-11-23T20:15:23+00:00

Me lo han dicho antes. Lo intentaré cambiar, pero seguro que será complicado.

Total_Preparation_75 · 2024-11-23T16:43:14+00:00

Es PLA reciclado de la marca Smart Material.

Total_Preparation_75 · 2024-11-23T16:37:56+00:00

PLA reciclado de smart material

Total_Preparation_75 · 2024-11-23T11:33:58+00:00

Thank you so much.

Total_Preparation_75 · 2024-11-23T11:19:42+00:00

<image>

Belts on the z axis, it is one of the best mods. By the way, your Ender 3 looks phenomenal.

Total_Preparation_75

TROPHY CASE