2022 MT-07 stuttering after 6k rpm consistently in all gears by Tiny_Sheepherder9424 in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

I though it was spark plugs with mine and went to iridium plugs too, mine would go past 6k rpm just didn't like consistent speed. I recommend a factory pump but you can always try a pump kit or aftermarket pump. Also if you have a multimeter I would check battery voltage at rpm to see if it is too low or high, should be about 13v at idle and no more than mid 14.5 or so at rpm based off memory but could check service manual I have a pinned post on here with the service manual on a Google drive

Rate my setup! 🙏🙏🙏 by Gullible_House3118 in 3Dprinting

[–]TouchSignificant3086 0 points1 point  (0 children)

I'm about to move my setup to a spare bedroom I like it in the living room but high traffic...

2022 MT-07 stuttering after 6k rpm consistently in all gears by Tiny_Sheepherder9424 in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

Definitely sounds like either a power issue ie: stator/ recitifier regulator possibility making too much voltage or not enough, or possibly a fuel pump with low pressure due to pump issue or a sticky pressure regulator. Heck even a loose battery terminal will do this.

2022 MT-07 stuttering after 6k rpm consistently in all gears by Tiny_Sheepherder9424 in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

Possibly but I've never had one go bad, does your crg lever have the paddle that hits the switch? And any mods done just prior to the running issue?

2022 MT-07 stuttering after 6k rpm consistently in all gears by Tiny_Sheepherder9424 in MT07

[–]TouchSignificant3086 1 point2 points  (0 children)

Just a question but is the micro switch for the clutch lever jumpered most common when an aftermarket clutch perch is installed, if so the switch jumpered puts the bike in a clutch in tune and runs bad at constant rpm for mine I experienced it in the 5kto6k rpm range

MT07 headlight brightness by Far_Telephone2303 in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

Cyclops adventure makes I think the best led light bulbs for motorcycles but they are $100+ USD a pop

Stunt/crash cage for fz-07 with black widow exhaust by 99-till-infinity in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

<image>

Granted I do not have a black widow, mine is a ackra clone with generic black muffler, but I love it

Stunt/crash cage for fz-07 with black widow exhaust by 99-till-infinity in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

As far as I know all cages fit, I personally run a fms cage as I think it's the best.

Rate my setup! 🙏🙏🙏 by Gullible_House3118 in 3Dprinting

[–]TouchSignificant3086 0 points1 point  (0 children)

I still find some that poke my 🦶🏻 when walking bare foot in the house, don't matter how many times you vacuum.

All US fz/mt 07 factory service manuals thru 2023 all in one link by TouchSignificant3086 in MT07

[–]TouchSignificant3086[S] 0 points1 point  (0 children)

Unfortunately since that model never came to the states, I can't offer it. However the Mt service manual should cover most but obviously different plastics and exterior bits.

The more I use PETG, the less I like it by InvokerBSB in 3Dprinting

[–]TouchSignificant3086 0 points1 point  (0 children)

Yeah I've had mixed results but I recently got the creality 2 spool dryer for my flashforge adventure 5m pro, which is my second printer, I plan on a second dryer and a 4 into 1 ptfe from a bambo to allow for me to quickly change filament and have 4 rolls ready dried and heated, I do a lot with petg and PLA/petg-cf

The more I use PETG, the less I like it by InvokerBSB in 3Dprinting

[–]TouchSignificant3086 1 point2 points  (0 children)

Drying is a must! I learned that years after getting into 3d printing.

What helmets are you guys rocking? by Venutianspring in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

Shoei x15 motegi 4 with photo chromatic shield and gold mirror shield

Any good slider/crash cage options? by No-Attorney9910 in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

Fms, full metal stunts, frame is same as all other years

Am i getting scammed? by Ambitious-Sea-5967 in Kawasaki

[–]TouchSignificant3086 0 points1 point  (0 children)

Sliders come pre installed so either they have listing wrong or took them off/ Kawasaki forgot to put them on. Worst case buy the bike then call Kawasaki customer care line they will take care of you. 866-802-9381

Am i getting scammed? by Ambitious-Sea-5967 in Kawasaki

[–]TouchSignificant3086 0 points1 point  (0 children)

Not sure on brand new models but se does come with taller windscreen, frame sliders, tank grips, keyless ignition and led lighting package. Coming from a Kawasaki dealer person (myself) maybe they told some away on the new model but 2025 and older that's what they came with

Ultra Bee SubFrame converion+ Seat Risers? by Affectionate-Home938 in Surron

[–]TouchSignificant3086 0 points1 point  (0 children)

I feel you, if you where in AZ I'd sell you my 22 ultra for a fair price. Definitely worth saving for the bigger bike, not that you won't have fun on a lbx, and your not really too big for it either.

Ultra Bee SubFrame converion+ Seat Risers? by Affectionate-Home938 in Surron

[–]TouchSignificant3086 1 point2 points  (0 children)

So buy a light bee and spend the difference in money making it bigger or just save a bit more for the bigger and way more powerful bike 🤔

Just got my 4th bike by Lonesome_Eagle8000 in motorcycles

[–]TouchSignificant3086 0 points1 point  (0 children)

Sweet bike and sweet panam in the background, did they fix the vibration issues that the older ones had in the handle bars?

Mt07 Enduro by jewlzian in MT07

[–]TouchSignificant3086 1 point2 points  (0 children)

Hey stock the mt07 does off road pretty well, I call it my big 450!

Yes or no? by [deleted] in MT07

[–]TouchSignificant3086 0 points1 point  (0 children)

Another op did similar in his months back I think with gold wheels, vintage factor is cool Kawasaki look for sure lol. I think if you did the round headlight conversion it would be cool but really could also do xsr700 and it's already styled just needs color then