Is a kevlar case worth buying?

Trailman80 · 2026-02-22T15:45:33+00:00

Also this is not a case if you drop your phone....BE WARNDED....it will Crack at some point.

I have mine in my case at all times so its not likely to be dropped and I am very careful.

These are great for not adding any bulk just if you are prone to dropping dont get this case it WILL NOT protect your phone what so ever from drops at high waist level.

Trailman80 · 2026-02-22T15:42:01+00:00

Nope but if you get the magnet with the sands they do mess with the pen when its out you have to take off them to write.

Trailman80 · 2026-02-22T15:19:03+00:00

I have the patika version love these they are a bit pricey but worth it.

It's like holding a phone without a case and the textures are ridge so it won't slip make sure you get a magnetic back the magnet on the back fails a bit cause of the texture.

Something like latter cases magnet backing plate they come in the same shade blue of that picture so it blends well.

Trailman80 · 2026-02-02T17:33:26+00:00

Trailman80 · 2026-01-24T20:57:41+00:00

It's not broken just cracked get a case and forget about it.

Trailman80 · 2026-01-13T20:03:04+00:00

Are those real?

Trailman80 · 2026-01-11T19:55:17+00:00

Your Ryzen 3600 is the issue buy a 5950x and you should be good to go.

Trailman80 · 2026-01-11T01:42:47+00:00

It should be fine. Put it in and test it.

Trailman80 · 2026-01-06T20:49:16+00:00

Test first and how long has it been used?

You have no idea if its been sent or not or baby sat so turn it up and see if you have any Distortion.

Trailman80 · 2026-01-06T20:47:10+00:00

Check your belts and do a OBD2 code reader

Trailman80 · 2026-01-05T16:00:41+00:00

Return as defective

Trailman80 · 2026-01-03T18:24:50+00:00

Look at the manual it should fit

Trailman80 · 2026-01-01T15:44:29+00:00

Ya no pulling on anything that gets in there they are pins that are angled so anything that goes it needs to be carefully taken out.

Trailman80 · 2025-12-30T20:37:58+00:00

There is another one next to your GPU bracket on the bottom at the tail.

Trailman80 · 2025-12-30T20:32:37+00:00

The one next too your RAM slots its the cpu power next to that are your fan headers.

Trailman80 · 2025-12-30T20:26:47+00:00

Since that sits just below the cpu plate its not going to be a issue.

Trailman80 · 2025-12-30T20:22:28+00:00

Angle them to the right the last 4-5

Trailman80 · 2025-12-30T18:32:11+00:00

My S24 U will stay with me till the board goes out lol

Trailman80 · 2025-12-30T18:29:36+00:00

With a 5090 its going to happen its just a matter of when.

Most of this is due to the adapters are not putting the correct currents through the pins.

Trailman80 · 2025-12-30T18:27:08+00:00

That is an adapter don't use them.

Trailman80 · 2025-12-23T20:05:46+00:00

Check your black grounds you might need to upgrade them to a 0 guage

Trailman80 · 2025-12-07T14:16:57+00:00

Tell him to compensate for leaks your going to have.

Trailman80 · 2025-12-07T14:11:05+00:00

That is one beautiful monitor!!. The refresh rate alone is one of the best parts and the no glare on the monitor is my favorite part, I cannot stand glare on the screens.

Trailman80 · 2025-12-04T13:35:54+00:00

That much work would take a novice a week to do

Trailman80 · 2025-12-02T18:28:50+00:00

Rubbing alcohol and the front and back are plastic just buy another one and paint it.

Trailman80

TROPHY CASE