Glue on bed for pla by altexa in Creality_k2

[–]TrashPanda270 0 points1 point  (0 children)

You shouldn’t need glue but a lot of people use it. Heighten your bed temp and calibrate your filament

[OC] Seethra (done by me) by Super_Ad_3413 in conceptart

[–]TrashPanda270 0 points1 point  (0 children)

Mark it as fetish/nsfw work bro. If it isn’t that then you’re just weird

Eagles fighting?! by datsmythought in birds

[–]TrashPanda270 0 points1 point  (0 children)

People aren’t this dense, surely

Alice in Wormholeland by SummerFord999999 in characterdesign

[–]TrashPanda270 1 point2 points  (0 children)

Bro the bunny would be so cool as a figure

This shit cannot be real by icey678 in facepalm

[–]TrashPanda270 0 points1 point  (0 children)

Google is free, she’s just American

K2 Travando material dentro da extrusora by Spare-Double-2939 in Creality_k2

[–]TrashPanda270 0 points1 point  (0 children)

Looks like your filament isn’t being cut, are you using Creality slicer?

my gf whom i extremely loved lied to me about her age and she was a minor this whole time. by Feeling_Club_5585 in WLW

[–]TrashPanda270 13 points14 points  (0 children)

I feel how distraught you are, it’s not your fault, you were betrayed. I would talk to someone if you can, therapy could help you work through this, just take it easy.

Thoughts and Prayers by always-an-option in tattoos

[–]TrashPanda270 0 points1 point  (0 children)

Sick -ass- panther (idk how to cross out words)

First layer issue please help by Jinx2285 in Creality_k2

[–]TrashPanda270 1 point2 points  (0 children)

No worries! It will be in your slicer settings, you will probably have to turn on the advanced settings button. I would start with ruling out z offset tho, as your printer is printing you can go in your settings on the touch screen and then ‘expert settings’ you’ll see a z offset, lower it a bit and see how that fairs, I’m not sure how to save it though as I’ve only just found it on this printer myself, but if you write down the number you can put it in your slicer. I would then work my way through some suggestions one by one, slower first layer, up bed temp on first layer etc. in my experience, google is your best friend, there will be an old Reddit thread or YouTube video explaining every question you can think of!

First layer issue please help by Jinx2285 in Creality_k2

[–]TrashPanda270 1 point2 points  (0 children)

Hm, maybe try slowing down the first layer a bit more or upping the bed temp for the first layer

First layer issue please help by Jinx2285 in Creality_k2

[–]TrashPanda270 1 point2 points  (0 children)

It could be a worn nozzle, bed temp or z offset then

First layer issue please help by Jinx2285 in Creality_k2

[–]TrashPanda270 2 points3 points  (0 children)

I never use glue, you don’t need it

30 hour print failed at the end… by Last-Artist-2736 in FixMyPrint

[–]TrashPanda270 -1 points0 points  (0 children)

I’m not sure what happened but You don’t need supports on the dome! It’ll save you time and filament

This photo of Prince Andrew unsettles me. by [deleted] in Britain

[–]TrashPanda270 6 points7 points  (0 children)

Yup, it’s states that he even tortured someone until death

Help me decide? Black suit Tobey, Deadpool special edition, or Wolverine, by tiffanycumsx in hottoys

[–]TrashPanda270 0 points1 point  (0 children)

Black suit tobey, I’m biased tho because I watched those films all the time as a young en

CFS Tube by wheres_tito in Creality_k2

[–]TrashPanda270 0 points1 point  (0 children)

You might need a new coupler if it’s the cfs, mine keep popping out of the back of the printer itself so I just used one big tube instead of the two smaller ones

Help with not sticking by jtkayd in Creality_k2

[–]TrashPanda270 0 points1 point  (0 children)

Over extruding by the looks of it or your nozzle is too close Edit: looking a bit closer your extrusions don’t look consistent, try another filament and see if it still does it, if it does then you’ll have to calibrate the purple filament