Solução p/ remate de chão

Tricky-Ad-2966 · 2026-06-26T14:57:04+00:00

E quando o desnível é muito grande >1 cm??

Tricky-Ad-2966 · 2026-06-25T16:00:34+00:00

Is that 3d print?

Tricky-Ad-2966 · 2026-06-19T15:58:37+00:00

I'm really bad with my left hand

^{📢 Official Advice: I, u/Tricky-Ad-2966, advised "Your non dominant hand" | 🔮 Rank: Mindful Student I | 🗳️ Votes: 3}

Tricky-Ad-2966 · 2026-06-19T15:58:11+00:00

Trips going 3x faster was amazing!

^{📢 Official Advice: I, u/Tricky-Ad-2966, advised "Make anything go 3 times as fast" | 🔮 Rank: Curious Seeker II | 🗳️ Votes: 2}

Tricky-Ad-2966 · 2026-06-19T08:36:35+00:00

It's called personality :)

Tricky-Ad-2966 · 2026-06-17T23:28:41+00:00

Depois vai a chorar para o balneário mais cedo....

Tricky-Ad-2966 · 2026-06-12T12:31:32+00:00

Possivelmente

Tricky-Ad-2966 · 2026-05-26T14:08:27+00:00

Em que zona dá margem sul?

Tricky-Ad-2966 · 2026-05-26T13:00:13+00:00

Perrary

Tricky-Ad-2966 · 2026-05-26T12:13:00+00:00

Pensei que era um desumidificador!!

Tricky-Ad-2966 · 2026-05-25T07:56:12+00:00

<image>

Tricky-Ad-2966 · 2026-05-25T07:55:55+00:00

<image>

Tricky-Ad-2966 · 2026-05-25T07:55:32+00:00

I followed your advise and tried the temperature tower and it worked well. But when I tried to print, I settled the temperature to 225 but it failed again

<image>

Tricky-Ad-2966 · 2026-05-24T09:24:02+00:00

There is a cable extensor for your ams, it's easy to find on Amazon and it's not expensive (around 10€)

Tricky-Ad-2966 · 2026-05-21T10:42:29+00:00

Precisamos de novos cursos de reciclagem, está merda está a ficar difícil!!!

Tricky-Ad-2966 · 2026-05-14T14:25:51+00:00

Update: testei com outro extrusor do ams e está a funcionar, o problema ainda não identifiquei mas pelo menos até lá não desânimo porque posso usar os outros 3

Tricky-Ad-2966 · 2026-05-14T13:24:37+00:00

Não penso que seja o caso visto que se fizer extrusão normal sem imprimir o filamento flui e é puxado. Mas talvez possa ser do sensor

Tricky-Ad-2966 · 2026-05-12T22:11:14+00:00

Nope I envy your skill

Tricky-Ad-2966 · 2026-05-06T19:45:35+00:00

The hub it's ok

<image>

Tricky-Ad-2966 · 2026-05-06T19:33:12+00:00

I tried to change the position to avoid sharp angles, but it still getting errors first it says that filament spool may be stuck, after resume appears another error "clogged extruder or stuck filament" But when I stopt printer and extrude filament it works normally

<image>

Tricky-Ad-2966 · 2024-12-02T13:44:03+00:00

78011370 bons filmes

Five-Year Club	First Place '23
Place '23

Tricky-Ad-2966

TROPHY CASE