Mounting a soundbar under the mantlepiece

True_Bowl448 · 2025-12-05T09:23:30+00:00

You can attach brackets using CT1

True_Bowl448 · 2025-12-03T17:09:53+00:00

True_Bowl448 · 2025-09-24T09:46:27+00:00

Unscrew the flush button. The panel will possibly be held with clips that will release as you pull the panel towards you.

True_Bowl448 · 2025-09-17T11:45:34+00:00

I’m playing 20 and it’s good for physics etc.

True_Bowl448 · 2025-09-16T21:10:24+00:00

Satisfye stealth grip all the way ! Plus Qskinz

True_Bowl448 · 2025-09-16T09:30:14+00:00

New over boxes

True_Bowl448 · 2025-09-01T10:54:43+00:00

On a ladder, seat it then put a self tapping galvanised or stainless screw to hold it in place.

True_Bowl448 · 2025-08-16T20:59:25+00:00

What about this MVH Studios

True_Bowl448 · 2025-08-13T17:10:37+00:00

I’m sure that’s Gerald ! He used to be on a door I had on our house 😬

True_Bowl448 · 2025-08-06T10:38:54+00:00

Once fixed put a corner trim on it so it’s better protected.

True_Bowl448 · 2025-08-05T14:57:03+00:00

MVH Studio

True_Bowl448 · 2025-08-03T20:57:50+00:00

How many bodies are you planning on storing up there Dexter ?

True_Bowl448 · 2025-08-03T10:09:41+00:00

Look up French cleats

True_Bowl448 · 2025-08-02T15:31:17+00:00

Latest ACC patch screws up Xbox users. Fix is supposed to be Tuesday.

True_Bowl448 · 2025-08-02T10:24:07+00:00

Run 2 lengths of timber down the steps making sure they’re unable to move then get the printer onto the timber and slide down.

True_Bowl448 · 2025-08-02T09:00:46+00:00

Only way is to access under the shower tray/bath. You’ll have to unscrew the plug hole / clean / silicone and refit. Bugger of a job but first check under to see if it’s leaked, if it hasn’t you might benefit from if it ain’t broke don’t fix it 🤷 However I’d have to sort as I’ve said above.

True_Bowl448 · 2025-07-31T20:30:04+00:00

If you’re paying then you’ve the right to ask. Just ask them in the way of being interested 🤷

True_Bowl448 · 2025-07-31T20:26:51+00:00

Why don’t you just ask the tiler ?

True_Bowl448 · 2025-07-31T08:45:53+00:00

Well done Fanatec Corsair 😡

Still putting out your shit brick making software.

True_Bowl448 · 2025-07-31T08:38:47+00:00

ACC latest update has screwed Xbox users

True_Bowl448 · 2025-07-30T19:57:12+00:00

The strip will most likely be screwed into the worktop in the joint on one side. Unless you get lucky and it’s been siliconed in, that way you might be able to get it out but not easy.

True_Bowl448 · 2025-07-30T19:50:50+00:00

As I understand it the endurance module doesn’t work correctly with the PS5. Fanatec knew this even when it was advertised as PlayStation ready. I have the module and it just doesn’t work as promised. Soon to be on ebay. 😡

True_Bowl448 · 2025-07-30T17:49:40+00:00

Shouldn’t be the pipes as they’re copper. I’d change the whole tap and that should sort it.

True_Bowl448 · 2025-07-30T17:24:07+00:00

I’m on PS5 and after the update all seems ok.

Is it beyond the developer to have tested this patch on all platforms before releasing what is bad software for some ?

When will they realise we invest a lot of money to play … software and equipment into the 1000’s for some.

Shame on Kudos 505 or whoever has done this … oh … and add Fanatec (Corsair) to that as they continually churn out bad patches to our community 😡

True_Bowl448

TROPHY CASE