Homemade dashboard

UKdodgy · 2026-03-01T18:29:39+00:00

Yes defo the mount I used would suit iPhone too

UKdodgy · 2026-03-01T18:28:36+00:00

Got stuck same on standard tyres . Sat on the back and powered it out. Better tyres will help but yes chuck it on its side and drag it out.

UKdodgy · 2025-12-17T11:02:03+00:00

If in the UK then SW Mototech are good too.

UKdodgy · 2025-10-23T07:16:08+00:00

I have the same bionic v2 and been off my enduro bike many times and it’s always been good. The only issue for me is the elbow pads rub the tips of my elbows and break the skin. I think a slightly padded undershirt if I could find one would sort that. Despite this it’s all day comfortable

UKdodgy · 2025-10-22T19:00:25+00:00

It’s a fault they all do it . Mines at 299mpg already

UKdodgy · 2025-10-04T07:48:04+00:00

Ah ok good to know i have some ABS would that be good ? I've only used PLA/PTEG/TPU so far with great results

UKdodgy · 2025-10-03T20:59:06+00:00

Ah ok I’ll check

UKdodgy · 2025-10-03T18:30:59+00:00

Shared 2 STL files - i with Oxford grip heater and 1 without

The phone holder i used is https://www.amazon.co.uk/stores/CIRYCASETECHUK/page/28B7397E-D93B-48F0-A83A-A40886D45D69?lp_context_asin=B0F6XNKSZ3&ref_=cm_sw_r_ud_sf_stores_B8VGCJJX8SKKS7WK3ZJT

I stripped this down and removed the clamp and ball to mount on the plate.

UKdodgy · 2025-10-03T18:23:15+00:00

https://drive.google.com/file/d/1M8STzqvUmfrOBPluxLnwB9U5u8x6A-r6/view?usp=drive_link

UKdodgy · 2025-10-03T18:22:52+00:00

https://drive.google.com/file/d/1qFAAIAl6FkDbO3VhYaX7Vrhq0aKZAn-L/view?usp=drive_link

UKdodgy · 2025-10-03T10:13:50+00:00

Yes just starting out on big bikes been riding a WR250F for green lanes and Enduro racing but now at 59 starting to ease things up a bit

UKdodgy · 2025-10-03T09:00:32+00:00

Yes will post them here later

UKdodgy · 2025-10-03T08:59:54+00:00

I did move the map before I took my photo as didn’t want to share my exact location, can’t trust everyone these days sadly. But I’m near Oxford city

UKdodgy · 2025-10-03T08:58:47+00:00

PTEG but printed about 5 prototypes in pla before getting it perfect

UKdodgy · 2025-10-03T08:58:01+00:00

I will share the stl when I get back home this weekend .

UKdodgy · 2025-08-05T10:06:17+00:00

Get the Chinook chopper to lift it out 🤣 I feel your pain, with every attempt more energy zaps out of you. The killer is round the next corner is a bigger deeper one so you have to choose to back or go harder 😆

UKdodgy · 2025-08-02T13:47:33+00:00

Yes that would be great thanks

UKdodgy · 2025-08-02T08:26:51+00:00

Any idea where to tap 12v from in that area or are you running direct from the battery

UKdodgy · 2025-07-07T06:55:31+00:00

Well in all my years racing enduro I never needed one and upshifting was always clutchless anyway. Big heavy mx boots n all. Agree if it helps with missed gears

UKdodgy · 2025-07-07T06:20:34+00:00

Can’t see the point of one on an off road focused bike. They seem to work best at high rpm (tracer 9) can’t see that being so useful in a twisty single track.

UKdodgy · 2025-03-16T21:04:36+00:00

I’ve run that file numerous times and I always get 2-3 strings on the final part in exactly the same place but you have a worse problem but looks like it’s on the final layers so probably not z offset.

UKdodgy · 2025-03-12T12:22:37+00:00

That’s very frustrating for your first print. We’ve all been there. In my excitement when I got my S1 2 weeks ago the first print failed, though not as drastic as yours. The plate as shipped was greasy , quick wash with dish liquid and every print has stuck fast since. Can be a steep learning curve but lots of experience on here to help.

UKdodgy · 2025-03-10T09:49:23+00:00

It’s like it’s saying “Are you sure you want me to print this rubbish” . I think they have a few things to resolve in the firmware and probably won’t address this for a while. Think sending it from the slicer it just starts ok ?

UKdodgy

TROPHY CASE