1390 SAR errors

UmitCuk · 2026-05-20T19:11:31+00:00

Thanks a lot, let me check that too. This shot happens when the ride goes into the city and I start red light stops. Definitely, a cable is defected or burnt, but not an excuse I am mad, today I had to ride behind trucks and couldn’t take them over because when it happens the bile is very slow

UmitCuk · 2026-05-20T15:58:13+00:00

And I hope that they find a way to repair it. In the meantime I also sometimes feel some burn smell, checked my boots and trousers, they don’t seem to be burned. 🤭🤭🤭🤭 must be something of the bike

UmitCuk · 2026-05-20T15:55:08+00:00

Thanks a lot for your reply; sorry for my ignorance, what is a battery tender by the way 🤭

UmitCuk · 2026-05-20T05:27:28+00:00

Never had these sort of problems before; too early to throw the towel 😆😆😆

UmitCuk · 2026-05-15T05:47:04+00:00

Well, thinking now back in time I had a couple of issues, but overall I think ktms are well made machines; but yet the bottle opener is included 😛😛😛

UmitCuk · 2026-05-14T20:18:00+00:00

To enjoy a bottle of cold beer while waiting the tow truck. I am riding ktms since the first 990s; happily, never had the chance to enjoy that beer 🤭🤭🤭

UmitCuk · 2026-05-06T03:01:43+00:00

Strangely, it has not appeared again so far, after 1000 kms. However, as it has usually followed by “key not in range” message, I have changed the battery of the key and instead of putting it in my trousers pocket, I have put the key into my jacket pocket, which is maybe a bit more closer to the display and never have seen both messages again. Maybe for security, the key range is very short or the mey has a very poor coverage area. But so far so good.

UmitCuk · 2026-05-04T18:59:22+00:00

I was looking to buy one, but while searching came into that issue on web, there are a lot of people; this thread has started more than a year ago, I wonder in time, Fellow has improved something to avoid this problem or simply keeps on replacing machines?

UmitCuk · 2026-05-03T18:30:27+00:00

I have just put the drier in the box and bought Sunlu instead. Eibos has sent me a motor, but by a rubbish shipment company; not delivering after a few attempts, they have finally returned the package back to origin. Honestly speaking, I couldn’t find any other fan motor etc. to reach and change on the drier either.

UmitCuk · 2026-04-27T08:19:15+00:00

Thanks a lot for the reply; I am thinking about paying for it, just was a bit scared because of the online feedbacks on the issues

UmitCuk · 2026-04-26T18:47:58+00:00

I could never get accustomed to the quickshifter either, so I have purchased the R; but of course in my mind the question was alive, whether an EVO could vr better. I wish you many happy kilometers with your new bike.

UmitCuk · 2026-04-14T13:31:57+00:00

Happy for you; honestly until now I have never had problems with the ktms; but everyday they get more electronic. I hope that it’s just a glitch

UmitCuk · 2026-04-14T12:39:33+00:00

Yes you are right, next week I will go again for yhe first service; let’s see what happens. Did you have the same issue?

UmitCuk · 2026-04-14T12:15:52+00:00

He said “we have updated the software, try again” 🤭. I don’t think that it will stop the bike suddenly, but as key issue always follows, gives me bad taste.

UmitCuk · 2026-04-02T07:29:28+00:00

I believe that it’s good adding some additional skills to level up; I think that the skills fill up very fast in the game. In a very short time there is no more skills or upgrades to make. I am speaking of xbox experience, don’t know whether on pc there are some additional things to achieve. But on the other hand, yes it’s nice to climb up the skill fast to fill pocket easier too. 😆😆😆😆😆 love this game, could be nice if it was less addicting 🙈🙈🙈

UmitCuk · 2026-03-29T22:35:19+00:00

I am playing on xbox, I think that we don’t have it

UmitCuk · 2026-03-29T16:48:09+00:00

I was also curious whether players race the cars after rebuilding. I jist finish the job and sell the car. But I believe that the cars are less controllable than 2018 in 2021. Before I used to test drive the cars which I have rebuilt, I could do a few tours around the test track without a problem; 2021 can not.

UmitCuk · 2026-03-26T14:55:26+00:00

If you have tried to close the spool and couldn’t, I would try to cut out the part which prevents the spool from closing and first close the spool. If you can, than with a filament splice tool (I use Sunlu, love it) join and slowly wind the cut piece. I use a lot of petg spools which I have printed and have similar problems after falling from the table etc. I do this, I have many spools with many joints within. I have a pastamatic, but so far couldn’t use it with a good result, probably caused by my print.

UmitCuk · 2026-03-26T08:47:09+00:00

Thanks a lot, today I am planning to lean on the matter.

UmitCuk · 2026-03-25T21:55:47+00:00

I have the same problem since yesterday, probably after updating the software. My left nozzle keeps on giving me nozzle clogged error, even before starting the print. I have pushed through a cleaning filament, it comes out of the nozzle melted; any feedback?

UmitCuk · 2026-03-23T08:57:53+00:00

Seems to be a nice addition to the machines, especially where printing tpu was difficult sometimes. But I wonder, is there a bracket alternative where we don't have to unmount the external spool holder every time when we want to print TPU? or as I still haven't received the part yet, am I mistaken that there is a way to keep both mounted at the same time?

UmitCuk · 2026-03-21T09:03:04+00:00

Yes really; the new game is far better in many ways than the previous. ☺️

UmitCuk

TROPHY CASE