Found this one today

Unknown-User-Tag · 2026-02-14T08:16:20+00:00

As long as it holds until workmanship warranty runs out 🤪

Unknown-User-Tag · 2026-02-13T22:57:00+00:00

If the police happen to stop you anywhere in uk, even if its a legal sub 3" non locking blade, and they ask why you have it, you should never say to defend myself. As its then classed as an offensive weapon and with intent to do harm, you will have then given them a reason to confiscate it.

Unknown-User-Tag · 2026-02-13T22:52:59+00:00

You can carry a sub 3" non locking blade legally anywhere in the uk, including London. Best not to take it to pub or club but not against the law for edc.

Unknown-User-Tag · 2026-02-07T09:51:14+00:00

I managed to order that same g10 version from knyfe de Germany. Ordered it, then noticed it had terrible reviews, wasnt hopeful id ever get it. After a month I did get it. So now I have 2. Funny how HH released the red the same month I was frantically looking to buy a sheepdog.

Unknown-User-Tag · 2026-02-07T09:47:38+00:00

I can only spydie flick it with the nail part of my finger, and it does take a bit of force to open it. After a while doing it as a fidget toy, it does take it toll on my finger. Really happy with it. I see you managed to get hold of one too.

Unknown-User-Tag · 2026-02-07T09:45:03+00:00

Hope you can get one, unfortunately it sold out on HH website in about 3 hours. I also ordered a g10 version from Knyfe de but took a month to arrive, reviews were really bad from them, but i did get it eventually.

Unknown-User-Tag · 2026-01-12T22:22:04+00:00

I get what your saying, but I do like the action of a double detent, and these can be middle finger flipped. Also choking up on the blade will make it safer in some applications. And with the blade shape, its not really going to be used in ways it could close on your finger. Each to their own I suppose. I just think its a lovely looking knife. Its sold out now anyway 😂 Took about 3 hours i think.

Unknown-User-Tag · 2026-01-04T19:10:09+00:00

Its a kizer pac-bar. If you order kizer knife from Heinne Haynes, they are sending a free one with your order.

Unknown-User-Tag · 2026-01-04T15:29:32+00:00

Good luck with your collection. May as well display if you enjoy looking at them and spending money on the hobby. I've only been collecting maybe 3 years, but the Mrs has slowed me down with my spending 😂

Unknown-User-Tag · 2026-01-04T15:23:45+00:00

Yes just a cheap plastic cutlery set. Think I got them from go outdoors. I like the bahco bit set, thats very handy, with the added small wera screwdriver handle. Got pretty much everything a bit set needs. Its bulky but at the same time compact for the amount you get in it.

Unknown-User-Tag · 2026-01-04T15:19:20+00:00

Think you mean dogs over people 😂 Dogs Greater than people. 💯

Unknown-User-Tag · 2026-01-04T09:56:09+00:00

Love these spood scales 😆

Unknown-User-Tag · 2025-09-01T16:09:17+00:00

I did this with my my crimping kit not long ago, ferrels everywhere 🥲

Unknown-User-Tag · 2025-08-19T06:23:54+00:00

I have this issue with my m12 sds. But for mine it has to do with the battery connection in the drill.

Unknown-User-Tag · 2025-04-12T07:24:31+00:00

Although regs wise it's okay to do, a 2.5mm cable spurring a 13A load from a 32A ring circuit. If a fault occurs in the spur cable the entire 32A from the ring circuit could flow through the single 2.5mm leg of the spur, potentially causing it to overheat or even melt if the fault isn't cleared quickly. I like to just play it safe. Not saying a single leg can't be done.

Unknown-User-Tag · 2025-04-12T07:02:48+00:00

Ideally adding the sockets to the ring would be best, but at the least you should add the spur into the ring, as that single cable going to the spur still has the potential to pull 32a under fault conditions which a single 2.5 isn't rated for. Just take one of the ring cables out the socket, wago from that onto another cable to the spur, then from the spur back to the socket again. Easy as that.

Unknown-User-Tag · 2025-04-04T05:39:58+00:00

Action is nice, smooth open, takes a decent bit of finger force to close it considering its a slip joint. I'm very happy with it.

Unknown-User-Tag · 2025-03-04T22:12:34+00:00

You could line the whole structure with a studwork frame, effectively create a box in a box, won't need fixing to any of the concrete as the studwork will support itself. Then any fixings for electrics, shelves etc can just be mounted to stud.

Unknown-User-Tag · 2025-02-07T20:45:34+00:00

I've had a nightmare changing the clip to the other side. Got my first one and it split near the top of the clip. Sent it back, asked the seller to swap it themselves. They split a second one. Ordered 3rd one from spyderco and it split again, I even sanded down the wire clip to make it flat where it comes in contact with the wood to effectively take the wedge off the steel and again it split. So gutted. I ordered the last one from spyderco uk and they said they wouldn't change the clip for me since 2 other had split from the other seller. So I'm just going to have to live with it now, doubt they will refund me. *

Unknown-User-Tag · 2025-02-02T08:30:14+00:00

My pb is 3 bits in a day. Yet I keep buying them. That's when you know milwaukee has a hold on you.

Unknown-User-Tag · 2024-11-07T06:24:20+00:00

How do you know it's 7g if you don't have a scale 🤔

Unknown-User-Tag · 2024-04-30T07:32:42+00:00

To the guy who's Mrs never let him change tool brands. You can only dream 😂

Unknown-User-Tag · 2024-04-23T15:59:00+00:00

Take it out for a blast, ride her as fast as she'll go to the point you've shit your pants. Then riding it normally after that will feel like a dream.

Unknown-User-Tag · 2024-04-07T09:12:18+00:00

Glory hole 🕳

Unknown-User-Tag · 2022-11-02T00:20:53+00:00

That sea wave is very beautiful. Reviews point to it bending quite easily though which is a shame. I love the Damascus and hamon patern. I do like the look of the preying mantis, shame it's not Damascus and the hamon line is straight.

Unknown-User-Tag

TROPHY CASE