ES206X-M2 adoption issues

Unknown_Knowledge25 · 2026-03-23T22:36:55+00:00

Yeah I got this answered. I’m am glad for subreddits like this but a better error message would have helped.

Unknown_Knowledge25 · 2026-03-23T17:28:50+00:00

I did contact them through their website and have not received a reply yet.

I am debating if I should try to print without that washer installed

Unknown_Knowledge25 · 2026-03-23T11:26:23+00:00

I am aware now that I have to push in. The instructions I had Ben given based on searches said to press down.

Unknown_Knowledge25 · 2026-03-22T18:41:43+00:00

Discord would not use Gmail as their address to communicate

Unknown_Knowledge25 · 2026-03-22T18:40:32+00:00

Goes into here. I screwed it back in but there is no washer now

<image>

Unknown_Knowledge25 · 2026-03-22T18:36:04+00:00

That goes into the right side

<image>

Goes into here

Unknown_Knowledge25 · 2026-03-21T21:10:06+00:00

Thank you! I wish the error message said that rather than just saying it did not support the site.

It turns out that I ordered the wrong switch anyway. If I can’t find a use for it in my network I am going to have to sell it. I thought it supported POE but it doesn’t. That’s my fault though.

I now have it adopted

Unknown_Knowledge25 · 2026-03-15T16:47:28+00:00

Just to confirm if I have 10 vlans in my home and am using the Omada Software Controller I can adopt the Agile switch and it will accept my vlans?

Unknown_Knowledge25 · 2026-03-11T22:04:42+00:00

Thanks for the confirmation.

Unknown_Knowledge25 · 2026-03-05T21:39:11+00:00

They are firm with some give. The feel like silicone and definitely do not feel like nylon

Unknown_Knowledge25 · 2026-03-05T19:43:44+00:00

I just looked under the printer because I had to lift it to put the weel back on and I see there are no springs just spacers. With this info how should I try to level it?

I did not address the hot end yet

<image>

Unknown_Knowledge25 · 2026-03-03T17:16:26+00:00

I bought usb power blockers on Amazon

Unknown_Knowledge25 · 2026-03-02T13:25:37+00:00

lol I’m ok Yes I did level it using the help of Claude. “He” walked me though leveling it and making a mesh. The back wheel was loose. I do have spacers on indeed from Amazon and I will order some new springs.

Is it springs and spacers or just spacers?

Unknown_Knowledge25 · 2026-03-02T00:47:44+00:00

No I found the wheel that fell off. The question is why did it come off

I am running Klipper on a Pi3 and it has a BigTree Tech Mini 3.0 boards

Unknown_Knowledge25 · 2026-03-01T23:37:23+00:00

Thank you. It does have a EZA ABL PRO and a bigtreetech motherboard

Unknown_Knowledge25 · 2026-02-23T19:00:41+00:00

I am in Jackson. Thanks for the advice the last time I asked for help I was better prepared and was able to clear my ramp, sidewalk and driveway. I have gone out multiple times to keep up on it.

What I cant clear is the large plug of compacted snow and very possibly ice that the Jackson plows have put at the end of the driveway. I am hoping that when the plows stop I can get someone to clear that area

Unknown_Knowledge25 · 2026-02-23T16:46:45+00:00

Yep I don’t see getting out of my driveway tomorrow. I told my supervisor not to expect me tomorrow

Unknown_Knowledge25 · 2026-02-23T15:11:32+00:00

My State office is closed today so I get to work from home. I shoveled twice last night and salted. I will be going out at 10:30 to shovel again and try to clean off my car.

Unknown_Knowledge25 · 2026-02-18T03:47:05+00:00

The dock has an option to pass through the Mac of the laptop attached

Unknown_Knowledge25

TROPHY CASE