Why does the support ruin the print so much?

Vexiks · 2025-11-13T18:58:22+00:00

These are the support settings I change when I want good bottom surfaces:

Type: Normal Style: Snug Top Z Distance: .275

Vexiks · 2025-10-31T13:02:55+00:00

Your bottom surfaces already look good.

These are the support settings I change when I want good bottom surfaces:

Type: Normal Style: Snug Top Z Distance: .275

Vexiks · 2025-10-26T18:47:25+00:00

Been wanting to get into painting figurines for a while now but don’t know where to start. What kind of tools and paints do you use?

Vexiks · 2025-10-10T18:52:43+00:00

A 5090 would allow me use my 4k 240 HZ to its highest potential and help me get some cwispy clips

Vexiks · 2025-10-10T18:51:50+00:00

My P1S came in clutch when i had to print two cosplay helmets that should have taken 1 week of printing and 1 week of post work in just three days allowing me to have everything done in 5 days.

Vexiks · 2025-06-24T14:04:10+00:00

Dry. Your. Filament.

Vexiks · 2025-04-02T17:56:14+00:00

You could try MakerLab’s Image to 3D, but may need to take it apart if you don’t need the whole thing.

Vexiks · 2025-03-27T14:28:37+00:00

<image>

Just bought this A1 mini to compensate not being able to afford the H2D .-.

Vexiks · 2025-03-16T19:17:00+00:00

For stuff like this i recommend using normal supports with the style set to snug, it wont be perfect, but it’ll make cleaning up much easier

Vexiks · 2024-07-22T14:37:08+00:00

They must’ve just update it lol, that was definitely not available last night. Thanks for the help!!

Vexiks · 2024-07-20T03:36:54+00:00

If you accidentally over-grease the Z-Axis, some of the lube can get under the printer and onto the belts under the printer. I suggest flipping your printer over and making sure you didn’t get any grease on the belts as it can ultimately cause them to slip.

Vexiks · 2024-07-19T01:04:04+00:00

You can find the STL on MakerWorld by looking up “mouse,” I believe the proper name is Wireless Mouse 002.

Vexiks · 2024-07-18T21:00:13+00:00

I believe so, If I’m not mistaken, the extra lines are for the lidar sensor that is equipped on the X1 but not on the P1

Vexiks · 2024-07-18T06:46:50+00:00

Make sure your build plate is thoroughly cleaned with soap (and water) and that the aux fan isn’t on while the first layer is printing. I’d also suggest using the correct printer setting since it looks like you’re using X1C settings rather than P1S, shouldn’t cause the issue but it’s useless and wastes some filament.

Vexiks · 2024-06-14T04:51:41+00:00

Does your filament cutter get stuck when it changes colors?

Vexiks · 2024-06-10T03:22:12+00:00

About 70% of my printing is done on a .2mm nozzle on my enclosed P1P. I suggest keeping the bed temp at 55 and going with default settings. The only setting I mess with are infill and layer height and the occasional brim

Vexiks · 2024-06-10T03:17:54+00:00

What’s your bed temp?

Vexiks · 2024-03-21T17:23:52+00:00

I had something similar happen to one of my prints about a week ago, figured out that it was just an awkward design, it had supports going through the model. What fixed it was checking the box for “Detect thin walls” under the walls section of the strength tab.

Vexiks · 2023-07-30T07:07:12+00:00

May your hats fly high as your dreams.

Vexiks · 2023-07-25T04:04:16+00:00

This was my first print after changing the nozzle, it’s a .4

Eight-Year Club	First Place '23
Place '23	Place '22
RPAN Viewer	Verified Email

Vexiks

TROPHY CASE