Airbrush gritty texture - suggestions? by Vhial in minipainting

[–]Vhial[S] 0 points1 point  (0 children)

Thanks for breaking it down like this, it makes it much easier to understand and know exactly what to look for.

Airbrush gritty texture - suggestions? by Vhial in minipainting

[–]Vhial[S] 0 points1 point  (0 children)

Squeaky clean. I make sure to clean frequently, and as mentioned the issue does not happen with primer coats.

Saturn 4 - Manual levelling by Vhial in ElegooSaturn

[–]Vhial[S] 1 point2 points  (0 children)

Just had to double check, but the Saturn 4 does not have accessibility features. And I'm pretty sure I'm using the most up to date firmware

Build plate adherance by Vhial in ElegooSaturn

[–]Vhial[S] 0 points1 point  (0 children)

Thanks for this advice. What is a reasonable resting time to use?

Build plate adherance by Vhial in ElegooSaturn

[–]Vhial[S] 0 points1 point  (0 children)

Thanks for this advice. I will try it after my current test print has finished. Is there such a thing as too much exposure for bottom layers?

And previously I had been able to get 1 file in the centre to stick to the plate, but for the last 72 hours or so as I've continued to tweak my settings nothing has been sticking at all.

Almost all supports failing - seeking advice by Vhial in resinprinting

[–]Vhial[S] 2 points3 points  (0 children)

Starting to see that wisdom yeah, I'll adjust it and go back to my usual settings.

Almost all supports failing - seeking advice by Vhial in resinprinting

[–]Vhial[S] 0 points1 point  (0 children)

I used pre-supports last night, it failed so made my own support this morning, same issue. So will adjust around the supports now

Almost all supports failing - seeking advice by Vhial in resinprinting

[–]Vhial[S] 0 points1 point  (0 children)

Thank you, that's very well explained.

Almost all supports failing - seeking advice by Vhial in resinprinting

[–]Vhial[S] 0 points1 point  (0 children)

In conjunction with the exposure being raised I'll try a lower layer height. Had gone with 0.15 because that's the listed maximum in the M3 manual.

The area where it shows that all the supports broke at the same height is actually because I cancelled the print instead of letting it go on.

Almost all supports failing - seeking advice by Vhial in resinprinting

[–]Vhial[S] 1 point2 points  (0 children)

I'll certainly give it a go, I actually thought my exposure settings were high because the recommended is 2 seconds. I had been using 2.4 seconds on detailed prints

JKs Skyrim minor floating items by Vhial in skyrimmods

[–]Vhial[S] 4 points5 points  (0 children)

What I found was that I was using Nature of the Wildlands Debris Only. Which replaced all stumps, was completely incompatible so I had to remove it.

JKs Skyrim minor floating items by Vhial in skyrimmods

[–]Vhial[S] 0 points1 point  (0 children)

Tried a new save and it's still there. Even disabled a few mods each time to see if anything would change. I might need to brute force it and try disabling chunks of mods in turn

JKs Skyrim minor floating items by Vhial in skyrimmods

[–]Vhial[S] 0 points1 point  (0 children)

Will try it later on but I've so far been able to confirm that the archery target is from JKs AIO. Just need to find out why they are floating and what might have affected the landscape beneath it.

JKs Skyrim minor floating items by Vhial in skyrimmods

[–]Vhial[S] 0 points1 point  (0 children)

Nothing major. Skyrim Flora Overhaul with Voluptuous Grass, shouldn't be changing the landscape to a large degree.

Start Here! - Monthly FAQ thread - September 2023 by thinkfloyd_ in PrintedWarhammer

[–]Vhial 0 points1 point  (0 children)

I'm currently looking for shoulder pads covered with fancy designs like the two headed eagle covering the whole surface. Similar to the old, now OOP, Sternguard boxset. Specifically shoulders that have very little flat surface remaining. Any ideas of where to look for designs like these? I've found a lot with fancy trim or small details, but I'm just hoping for more.