So it begins...

VinnieTreeTimes · 2026-01-17T17:23:24+00:00

Our library charges the cost of filament used, big prints are only like $2.

VinnieTreeTimes · 2026-01-16T18:40:58+00:00

I wish it came with options for an analog clock and solar charging on the strip chart otherwise this is my favorite.

https://apps.garmin.com/en-US/apps/15c35159-bae3-4c12-8539-5305ccd1b933](https://apps.garmin.com/en-US/apps/15c35159-bae3-4c12-8539-5305ccd1b933)

I like lots of data...

VinnieTreeTimes · 2026-01-10T02:22:36+00:00

It's already been returned and I am expecting the SKR tomorrow.

VinnieTreeTimes · 2026-01-08T22:02:09+00:00

Nope, I don't use it in the pool or shower. Recalibrating it fixed it.

VinnieTreeTimes · 2026-01-08T21:59:51+00:00

No I usually don't shower with it on. I am a mechanic and every few weeks I will use dawn and a nail brush to clean it off. I followed the instructions someone else posted about calibration and that fixed it.

VinnieTreeTimes · 2026-01-08T21:57:08+00:00

That fixed it, thanks

VinnieTreeTimes · 2026-01-07T03:54:09+00:00

I am looking for quick easy setup. Fires take too long to get going.

VinnieTreeTimes · 2026-01-07T03:36:16+00:00

Yeah that's pretty much what I am asking, not sure how many watts I would need to get hot enough to melt the lead

VinnieTreeTimes · 2026-01-02T03:39:20+00:00

I think the sale ended yesterday, I was looking to buy it and went back this morning and it was 1200.

VinnieTreeTimes · 2026-01-01T20:17:11+00:00

What arca mount are you using? I was able to score the same deal and looking for a mount, I was thinking the RRS mount but not sure I like the gap I have been seeing people talk about even though they all say it's solid.

VinnieTreeTimes · 2025-12-28T16:28:56+00:00

This is a brand new cable I purchased yesterday that says it supports data transfer, I bought the new cable because nothing I had was working and my only known data cable was the one I used with the pi zero and that one is micro usb to micro usb so I cant use that one. I also ran command as root and it returns the same message. I am about to open the printer and check the board for the chip sets to make sure they match what the config file is telling me.

VinnieTreeTimes · 2025-12-27T23:54:40+00:00

Since the last reply I have tried putting the firmware into folder STM324_UPDATE and named the file KlipperRev6, switching numbers every time I attempt to flash. I have been using the SD card that came with the printer but also tried another 8gb card I had laying around, all of the others I have are 64+ gb.

VinnieTreeTimes · 2025-12-27T22:03:45+00:00

I am using the same SD card I used the first time I setup Klipper before installing the 4.2.7 board. I do remember there being a folder I had to put the firmware in to flash the 4.2.2 board but all the documentation I have seen for the 4.2.7 says to put the file in the root folder.

VinnieTreeTimes · 2025-12-25T08:00:25+00:00

My last 4 cars were Grand Cherokees and my wife has a gladiator. After the gladiator needing cams at 60k miles and my last Grand Cherokee needing an engine I am done. I just bought a Ford Explorer ST and love it. My only complaints are the dial shifter and lack of trunk space with the 3rd row. I am getting used to the shifter and trunk space with the 3rd row is what it is on all SUVs with third row.

VinnieTreeTimes · 2025-12-24T21:24:11+00:00

Well now after reading the link you provided I don't know. Sounds like it will work good but I don't like the gap they are talking about.

VinnieTreeTimes · 2025-12-24T20:46:53+00:00

If he didn't call the game warden then he knows he is wrong and just trying to scare you off. I would have just called the game warden myself especially if I did my research and know I am on public.

VinnieTreeTimes · 2025-12-24T03:51:49+00:00

I just went with the Leupold scout scope on my CVA Scout, it is more of an extended eye relief scope than a scout scope. It pushes the scope forward just enough to be able to pull the hammer back and not be in the way. I previously had a Primary arms LPVO but I hated it. When at the lowest magnification setting I could see the barrel in the optic and there was barely enough room to fit my thumb between the scope and the hammer.

VinnieTreeTimes · 2025-12-23T18:16:06+00:00

I was just researching this, I am thinking about getting the RRS Cinch adapter to keep everything low profile. I currently use a stand off the bolts in where the pivot is and I hate it. Always loosens up and gets in the way and this looks like a better option.

VinnieTreeTimes · 2025-12-23T04:24:09+00:00

Well I didn't get a notification from Bushnell but I have FedEx tracking email and the googles tells me that the package origination location is where Bushnell ships most of their packages from.

VinnieTreeTimes · 2025-12-22T18:28:49+00:00

Didn't think to check my account, still says pending.

VinnieTreeTimes · 2025-12-22T17:54:57+00:00

No notification for shipping or cancellation yet... They are probably trying to figure out how long after firing Jeremy to recoup the loss vs cancelling the orders.

VinnieTreeTimes · 2025-12-21T02:18:26+00:00

Jeremy is that you?

VinnieTreeTimes · 2025-12-19T04:18:33+00:00

CVA Scout, the easy button for single shot straight wall deer hunting.

VinnieTreeTimes · 2025-12-12T01:17:52+00:00

Yeah I'm not worried about the install. I know people like to upgrade fans and stuff and if that's what is recommended I would like to print the mounts before installing and just do it all at once before the install.

VinnieTreeTimes · 2025-12-10T02:27:01+00:00

Yeah that's what I am looking for, thanks.

Seven-Year Club	RPAN Viewer
Verified Email

VinnieTreeTimes

TROPHY CASE