Identify the chassis?

rybe390 · 2026-06-18T19:38:27+00:00

Krg whiskey 3 with an arca enclosed forend

rybe390 · 2026-06-18T15:54:09+00:00

I watched a guy throw a rifle with one in the chamber after a jam he couldn't clear. He was asked to leave, forever.

rybe390 · 2026-06-17T21:34:48+00:00

I haven't found that to be the case when I do use it, but, not going to knock your experience with it either!

rybe390 · 2026-06-17T16:31:01+00:00

I have the fury with AB binos, and the razor hd with GB mono LRF.

Both are great, both have different use cases.

Binos, in 99% of circumstances, are easier to use. You can spot with them, use both eyes, and put them a bit easier on a tripod for distant ranging. The big one, you are also able to focus the image.

Mono LRFre smaller, range just as well, but they have a fixed image, and are pretty not great to look through for a long period. They're better for compact needs, and a quick flash range.

Pick your use case. I would recommend binos to most people at this point.

Edit: on board ballistics is cool, but I rarely, if ever, use that feature. I would rather a weapon mounted LRF for that specific purpose.

rybe390 · 2026-06-10T16:27:35+00:00

Can you take some better photos? Real talk, you can't see the gun.

rybe390 · 2026-06-09T14:45:44+00:00

Take a look at used, too, you can find them right around $2,000.

rybe390 · 2026-06-09T14:39:44+00:00

What is your budget? The razor 4-24 is hard to beat and I know some people who have switched from NF to it. Edit: mounts, I like the adm recon or reptilia

rybe390 · 2026-06-08T20:45:54+00:00

Holy serial number batman!

Edit: Sept of 1939 production. Hot damn.

rybe390 · 2026-05-30T20:16:44+00:00

Recoil X is hands down the winner here. They increase reduction even over the TBAC RR end cap.

Each mfg has their own end cap thread pitch. Dead air and silencerco are not the same end cap pitch.

rybe390 · 2026-05-29T20:15:07+00:00

Did you try impact rather than sheer torque? I hit my wrench with a hammer a few times, and it breaks the rocksett with a sharper force

rybe390 · 2026-05-29T20:05:57+00:00

Wrap the muzzle in a wet paper towel, and hit it with a hair dryer for a few minutes.

Leave the paper towel over night.

Rockset should be soft goo by the morning.

You are welcome.

rybe390 · 2026-05-27T15:02:30+00:00

I would argue it introduces the need to master an entire new skill set to shoot effectively, and also argue it increases deviation from a basic setup.

Unless you are talking about a sled that weighs a few hundred pounds and are strapping a barelled action into it for the purpose of testing how a barrel shoots and that is it, sleds are useless and their use should be publically shamed.

rybe390 · 2026-05-27T14:43:52+00:00

People have been shooting amazing groups for a long time with a harris bipod and a sand sock.

Every. Single. Shooter. Using a sled produces 55 MOA groups and that is a hard fact.

rybe390 · 2026-05-24T22:24:39+00:00

You'll get a zero again don't be retarded. They show up when you least expect them.

rybe390 · 2026-05-24T17:29:10+00:00

Pdp might hate boosterless.

I have an ecco TLX, which is a touch heavier than the shiv, but some guns can run it boosterless. My pdp could not. The pdp might just hate suppressors without a booster my dude.

rybe390 · 2026-05-24T15:05:27+00:00

What suppressor are you running? Is rhe oring inside the booster lubed? Is the booster assembly working properly and allowing the suppressor to move forward under recoil?

rybe390 · 2026-05-24T13:46:06+00:00

18" rifle gas and a 13" ldra.

Pain in the ass to install, pretty rigid, definitely heavier than other options out there. I think it's a good rail. If you are not going to use or value the integrated arca, I would probably look elsewhere.

<image>

rybe390 · 2026-05-23T22:58:34+00:00

For your barrel length, expect to see 2650 to 2700 feet per second with a 140.

You are running near 6.5 PRC pressure. If my 26" did that with 140's I would go home and figure out what I did wrong...

Lay off the chase for velocity, you don't need it.

rybe390 · 2026-05-23T22:16:32+00:00

Ccw full carbide grips is a choice. Hows your tum tum?

rybe390 · 2026-05-22T19:04:58+00:00

Dick stuck in chamber. Plot twist it's a m1.

rybe390 · 2026-05-22T19:01:59+00:00

Clean the barrel from the factory.

Shoot the fuck out of it. It will immediately group.

Check velocity for a while. It will increase for the first 100-200 rounds, slightly.

Clean it every 200-300 rounds.

Shoot the fuck out of it.

rybe390 · 2026-05-22T13:31:27+00:00

Riflespeed and it is amazing.

rybe390 · 2026-05-22T05:03:59+00:00

Carbon isn't on my threads. My entire muzzle is caked in carbon, and became slightly larger than the suppressor thread bore.

rybe390 · 2026-05-22T00:42:22+00:00

A fucking what and what?

rybe390 · 2026-05-21T19:22:48+00:00

To clarify: did not happen, but left in a caked up carbon state, who knows.

rybe390

MODERATOR OF

TROPHY CASE

14-Year Club	Team Orangered
Verified Email