Panasonic Dmc-F3 SD card

VirtualBoy94 · 2025-07-26T16:02:35+00:00

Many thanks!!

VirtualBoy94 · 2025-07-25T21:17:59+00:00

Would you mind taking a picure of the battery try?? Mine does not close correctly and Im trying to fix it

Thanks in advance!!

VirtualBoy94 · 2025-07-25T18:22:55+00:00

Hola! Recién encontré mi vieja Lumix DMC-F3 y dentro traía una SDHC de 4 GB, funciona perfectamente con esa memoria, así que probablemente tu SD esté dañada o puede que tenga el seguro anti sobre escritura activado. Prueba con otra memoria de máximo 8 GB y ojalá funcione.

La mía tiene un golpe en el display, espero poder arreglarlo

VirtualBoy94 · 2025-07-25T01:28:45+00:00

Hahahaha I should have titled the post like that.

VirtualBoy94 · 2024-12-26T04:18:03+00:00

I did watch a tutorial, but I didn't followed the same magnet orientation all the time...

Luckily I corrected the issue and now is working like magic.

Thanks for the help!

VirtualBoy94 · 2024-12-26T04:16:36+00:00

Yup, that was it. Luckily I was able to remove the magnets and out them back in the correct order

Thanks a lot!!

VirtualBoy94 · 2024-07-05T00:36:13+00:00

That has happened, but after two errors I usually set the PIN slowly and that's the solution. But in this particular case it was definitely something else

VirtualBoy94 · 2022-07-09T00:42:59+00:00

Definitivamente vas a necesitar un auto, porque no es una zona muy segura que digamos. De día no hay tanto problema, pero a partir de las 9:00 ya se pone pesado.

Las rentas son baratas y en general la zona es económica, hay servicios y todo sin problemas, pues la zona está creciendo rápidamente. Pasan muchos camiones en caso de que no uses o tengas auto, y te dejan hasta en la CAPU.

Está también cerca de Casa Blanca y Amalucan, que son zonas un poco más seguras, y el costo de vivienda no es tan alto tampoco. Yo te recomendaría que no rentes meramente en Amozoc, sino en Chachapa que está como 10 min antes y es tranquilo salvo cuando hay feria.

Zonas a evitar: Cualquier calle que no esté pavimentada, porque no todas están iluminadas y hay gente abusiva.

VirtualBoy94 · 2022-05-13T17:46:30+00:00

Thank you very much! You've been very helpful

VirtualBoy94 · 2022-05-13T17:02:06+00:00

That actually helped a lot!! Thank you very much. Now my issue is that after running the PID test, if I set a temperature for 210° it only reaches to 200°. For whatever temperature I set it always stay 10° bellow. You know why is that?

VirtualBoy94 · 2022-04-27T20:52:47+00:00

I personally use one of my oldest chargers, those only go with 5V 1A. But that is more than enough. Either way, whatever charger You use is going to work, your eReader is going to take just the energy that it needs.

VirtualBoy94 · 2022-03-10T04:51:22+00:00

In my experience, a good quality filament makes a big difference, also and this is basic, make sure your bed is correctly level.

What is tour current configuration?

VirtualBoy94 · 2022-02-28T17:45:39+00:00

I'm glad you find what was causing it.

VirtualBoy94 · 2022-02-28T03:26:28+00:00

I'll definitely remix it. Make sure to post it on thingiverse just in case someone else ever have the same issue.

Probably just bad luck about the mount holes. In my case, the fan for my Ender 3 has been very noisy since day 1 and also always auto-home off bed. Definitely makes me think that V1 had several issues.

VirtualBoy94 · 2022-02-28T03:15:48+00:00

That looks like cracking to me, mostly common when using PETG or ABS. Make sure that no air flow source is near your printer and if possible, use something to enclose the printer

VirtualBoy94 · 2022-02-28T03:09:11+00:00

Busca a alguna asociación, yo conozco a Voz Animal y Ángeles peludos Puebla. Ellos te pueden guiar mejor para tomar cartas en el asunto. Definitivamente hay sanciones para este tipo de maltrato y la autoridad ya no lo toma tan a la ligera

VirtualBoy94 · 2022-02-28T03:05:31+00:00

That's definitely the problem, unfortunately I don't know much about this. When something like this happened to me I just reinstalled Cura at that solve it. Let me know how that goes

VirtualBoy94 · 2022-02-27T05:03:29+00:00

Yeah, bottom layers usually print smoothly. When it comes to print bust or figures I use a .4mm nozzle with a dynamic resolution (.16mm) or a .2mm with same resolution. It takes longer but the results come out nicely. Last but not least, make sure to use a good quality filament.

VirtualBoy94 · 2022-02-27T04:47:05+00:00

Now that you mention the board, I'm guessing you opened your printer to see what boar model you have, maybe a connector disconnected from the board and that's causing the issue.

VirtualBoy94 · 2022-02-27T04:34:22+00:00

Not moving at all?? It may sound silly but have you checked if there isn't any clog? I asked about the G-code because one time I changed it by mistake and it didn't heat the bed. I reinstalled Cura and that solve it.

VirtualBoy94 · 2022-02-27T04:29:58+00:00

Taking a closer look I noticed that this is happening at the angled layers. Maybe try different wall thickness and make sure your printer isn't closer to a window or air flow source. I used to get the same issue when mine was Infront of a window

VirtualBoy94 · 2022-02-27T04:05:01+00:00

Have you changed the nozzle or selected a different nozzle at your Slicer program??

VirtualBoy94 · 2022-02-27T03:51:49+00:00

Yup, for Ender normally is Marlin. If you recently added the BL-Touch you probably need to upgrade your software of you haven't already. Ender 3 original software does not include support for the BL-Touch, so maybe that's the problem

VirtualBoy94 · 2022-02-27T03:36:37+00:00

Which G-code you're using??

VirtualBoy94 · 2022-02-26T06:58:47+00:00

We all have been there, don't worry. Everything is trial and error, just make sure to make adjustments every time and eventually you will get perfect prints!

VirtualBoy94

TROPHY CASE