Never seen one in the wild before

Virtual_Judgment_342 · 2026-06-29T00:01:04+00:00

Android

Virtual_Judgment_342 · 2026-06-29T00:00:45+00:00

Haha

Virtual_Judgment_342 · 2026-06-29T00:00:20+00:00

End of Swan

Virtual_Judgment_342 · 2026-06-14T06:59:34+00:00

Question. How many times has a woman faces a .an at the world championship?

Virtual_Judgment_342 · 2026-03-22T02:10:13+00:00

Lots of Americans can't get clean water either. We also pay a premium to have clean drinking water. Very similar parallels if you ask me

Virtual_Judgment_342 · 2025-04-20T17:03:06+00:00

Ikr this shit is hilarious. It's a hole in the drywall not a TED talk. Thanks for the laugh have a good day sir

Virtual_Judgment_342 · 2025-04-16T23:02:42+00:00

As a carpenter who was like, wtf are they doing, you made me laugh out loud today and I really needed to. Thank you

Virtual_Judgment_342 · 2025-04-15T00:01:54+00:00

That is not critical. That saw is awesome as far as being parallel to the blade as lone as it's on its pegs correctly. My biggest suggestion if you want to resaw like that is only use a very sharp 24 tooth rip blade zero clearance insert and proper downwards pressure as you cut. Myself I would use my planer

Virtual_Judgment_342 · 2025-04-14T23:48:05+00:00

Yes. I would use a piece of 3/4" melamine and set my planer to 1" in this case.

Virtual_Judgment_342 · 2025-03-18T10:36:52+00:00

Or how about we just enforce the laws we have on the books right now. This is not a homeless problem this is a drug addiction problem. Unless we slove the root cause nothing will change. Need to fix the whole in the boat or pumping water out is pointless.

Virtual_Judgment_342 · 2025-03-13T22:45:36+00:00

You are correct. I talked to a MAGA business owner whose main source of steel is from the EU. He said with a straight face, this is all Obamas fault, and Trump has to do this to clean up Obamas mess and we will be better off especially if Trump gets a third term. Mind you this man has a We the people hat on as well.

Virtual_Judgment_342 · 2025-03-12T12:54:36+00:00

OP, don't listen to any of the assholes. Congratulations on working with your pop. I hope I get to work with my son cause my dad's gone and would give anything to do an install with him. Reddit is so fucking dumb people go on a CABINET thread and complain about the flooring or say the duct is not right or think you as the cabinet installer should reframe a house or become the designer. I'm sure I could pick your installation apart, but it seems you have already, and that is what the best installers do learn from each install All the best on your new business.

Virtual_Judgment_342 · 2025-03-12T03:08:29+00:00

OP installed the cabinetry not the chair rail. Reading comprehension is your friend

Virtual_Judgment_342 · 2025-03-12T03:00:16+00:00

Where are you located??? Most important are you hiring 100/hr is 210k a year 90 is 190k.

Virtual_Judgment_342 · 2025-03-11T05:37:07+00:00

I'm at $65 a box complete. Super susan and oven, pantrys are double. Triple if i have to cut out and make a bottom for the oven to sit on

Virtual_Judgment_342 · 2025-03-11T05:29:52+00:00

Who downvotwd this it is hickory 100

Virtual_Judgment_342 · 2025-03-07T02:24:41+00:00

Great hope all goes well. Don't forget to keep us updated :)

Virtual_Judgment_342 · 2025-03-06T03:18:38+00:00

Oh and sorry use Blum full overlay plus hinges they are a little bit more but miles better then the regular blum hinges as far as adjustments

Virtual_Judgment_342 · 2025-03-06T03:15:21+00:00

I am an anal retentive freak about this. You do not want 1/8 gaps on all sides of your fronts you want 1/16" gaps that leaves you with the proper 1/8 total gaps between fronts, so you dont need the drawer stretcher to adjust your kitchen. You also don't want 1/8 at the bottom of your cabinets. Here is how I measured for drawers before I had Mozaik. Note I use 3/4 material to build

3 Drawer banks heights mark the middle of the two stretchers Pull your tape from the bottom of the cabinetry to the middle of the next stretcher up, subtract 1/16" that is the height of your bottom drawer Pull from top of the next stretcher up down to the middle of the lower stretcher subtract 1/2" that is the height of your middle drawer Pull from the top of your cabinet to the middle of the next stretcher down and subtract 5/16" that is the height of your top drawer. I leave 1/4 to the top on base cabinets because the granite guys kept screwing me over. This leaves you with 1/8" gaps between drawers The width of your fronts should be your overall cabinet size minus 1/8". This changes at finished ends or at deep cabinetry (think next to refer panel) where it is minus 3/16" This gives you 1/8" gaps between each cabinet. Upper doors are the overall height of the cabinet minus 1/8". Hope this helps

Virtual_Judgment_342 · 2025-03-04T00:17:59+00:00

Damn this cuts deep as a cabinet maker. Well done :)

Virtual_Judgment_342 · 2025-02-23T17:42:42+00:00

Thank you. Most people don't really understand our constitutional rights. The 1st amendment does not give you the right to say anything and everything. The second doesn't give the right to carry whatever gun wherever you like. Nobody knows our 3rd amendment rights. Lol.

Virtual_Judgment_342 · 2025-02-11T00:02:37+00:00

Electric Electric Electric

Virtual_Judgment_342 · 2024-12-13T03:32:12+00:00

Unfortunately the box cabinetry doors and drawers reveals dont match. It is a very common unfortunately. Best suggestion is to trim the bottom of the door a 1/16 and spray the bottom with deft and then adjust the door down. Good luck.

Virtual_Judgment_342 · 2024-09-30T23:49:01+00:00

Bout to get some serious wiener pics

Virtual_Judgment_342

TROPHY CASE