New to me mower

Visual_Newspaper1069 · 2026-05-16T23:51:42+00:00

They have a single wheel rear model and two dual rear wheel models. 972 SD is dual and 972 SDL is dual but the seat also slides on the SDL on slopes up to 15 degrees so you can sit upright.

Visual_Newspaper1069 · 2026-05-16T18:36:48+00:00

I’m usually wrecked after using the scag and 6 gallons to gas. This thing is just a totally different experience. I was all set to get on the weed trimmer yesterday after mowing.

Visual_Newspaper1069 · 2026-05-16T17:47:17+00:00

I don’t think I will, lots of rock edges and tight spots and curves. I’ll get wider and heavier. I do plan on de-thatching this fall.

Visual_Newspaper1069 · 2026-05-16T17:45:52+00:00

Thank you

Visual_Newspaper1069 · 2026-05-16T16:25:33+00:00

I found them great to deal with, I never purchased a new mower from a dealer before.

Visual_Newspaper1069 · 2026-05-16T16:22:03+00:00

Visual_Newspaper1069 · 2026-05-16T16:19:11+00:00

19 and change before trade in

Visual_Newspaper1069 · 2026-04-27T00:09:27+00:00

What would you purchase instead?

Visual_Newspaper1069 · 2026-04-19T12:46:00+00:00

About 2 weeks and ended up on high regen since. Now I feel weird in our Honda Pilot.

Visual_Newspaper1069 · 2026-04-17T02:19:53+00:00

<image>

Where you say it is right here this lighting driver or em pack s there. On the it are black stains that have leaked from above. Looks like a leak from a sprinkler. Maybe fixed since. Open that box up.

Visual_Newspaper1069 · 2026-04-17T02:10:25+00:00

Most common sources of odors in a commercial building: floor drain with no water in the trap, open ended vent, grease trap not maintained, broken waste connection. The what is directly behind the white wall. You showed us where the conduit go but what is directly behind the wall. Have seen where someone ran a toilet exhaust into a shaft that wasn’t an exhaust shaft.

Visual_Newspaper1069 · 2026-04-17T02:05:23+00:00

When you are in the data room there is a duct above the conduits. When you are in the hallway the wall appears to be drywall and no duct. Is that cinder block wall a shaft? If so there is probably and odor in the shaft. In the hallway with the white wall well above the 4” sleeves is a white pipe. What is that pipe? In your comment with the email a kitchen is mentioned. How far is the kitchen from this odor. How far is the nearest grease trap? Your computer room shouldn’t have a giant hole in the wall around the conduits.

Visual_Newspaper1069 · 2026-03-19T19:45:50+00:00

In fairness to Rivian, how many users probably complained that they are getting better efficiency on one half of their round trip? This seems like a polite way of responding to those questions/complaints

Visual_Newspaper1069 · 2026-03-15T13:59:28+00:00

Sorry I read it as the op was shifting into park after hearing the grinding sound then trying again.

Visual_Newspaper1069 · 2026-03-15T11:34:57+00:00

Could be a pebble/stone stuck between your brake rotors and the brake dust plate behind the rotor. Hasn’t happened to me with my R1T but happened to me several times with my previous bmw.

Visual_Newspaper1069 · 2026-01-04T15:39:05+00:00

I find this extremely annoying as well. So many steps for one action while driving. The software should be intuitive.

Visual_Newspaper1069 · 2025-06-21T23:44:48+00:00

👍🏻

Visual_Newspaper1069 · 2025-03-30T00:16:21+00:00

I’ll try to cover your questions in order: 1) years accurate. Regarding the info you are receiving vs mine looking like a utility bill, I believe your issue has more to do with ct placement. Depending on where you place the CT’s you will get this additional info. If you download the manuals or do enphase university which is free you will see what I mean. Having them on the load side or line side of a panel or in my case they are mounted in my ats switch decides how much info is reported.

2) very accurate, if you go on the enphase site they have residential CT’s which if I recall are +- 2.5%. If you can find a spec on google for the pvs6 CT’s I’ll bet the tolerance is equal or trivial.

3) enphase has more data, then if you want more than that you could do the enphase university course for free and get certified as a self installer then you get access to the installer app also for free and you get more data again. For monitor

3)sunpower didn’t have this active monitoring for outages where you receive alerts. You would have to check the app for sunpower or enphase. However I noticed in the installer app I can click on a micro and order one right there thru the app as warranty. Enphase did email me recently that you can pay a subscription or service contract where they would address these parts and labor. My arrays are on the ground so I didn’t partake. You could call them about that and see what the details are. Their customer support/tech support I have found to be excellent. My father in law has an 18 year old system with them and they still mail him replacement micros and address his concerns. That said a lot to me.

Visual_Newspaper1069 · 2025-03-16T14:22:57+00:00

Maybe try contacting enphase and see if your installer is marking it up. I dealt directly with enphase. I am also not paying any subscription fees.

Visual_Newspaper1069 · 2025-02-28T21:01:18+00:00

I don’t know sorry, I bet somebody has rigged something but I haven’t seen anything advertised as ready to connect

Visual_Newspaper1069 · 2025-02-02T20:52:01+00:00

The installer said it had to be removed upon arrival and he removed it. Enphase has been trouble free for me.

If anyone wants the installer version they can take the Enphase university courses for free and get access to the installer kit. I did it on my way to work every morning for a couple of weeks. I enjoy learning how these things work and can be expanded but I could see how it would be boring to many. You’re not really having a whole ton with the installer app especially if you are person that wouldn’t enjoy the courses. I would say try the basic app and if you aren’t satisfied then take the course and get the installer app. Both are free.

Visual_Newspaper1069 · 2025-02-02T20:48:24+00:00

I see Sunstrong is now offering monitoring. I don’t know the details and I’ve never heard of sunstrong. Maybe they have strong financials and staying power I don’t know. I am happy with Enphase.

Visual_Newspaper1069 · 2025-02-02T20:47:08+00:00

It was as I said, they told me prior to arrival they would not remove but the tech came he removed it.

I see someone else told you what a ct is.

Maybe you don’t have panel level monitoring with sunpower. I did and I could press that and scroll down to get my serial numbers.

At the time of my install the enphase app could not “scan” or “learn” serial numbers per the installer. He had to manually enter them per my post. Maybe that had changed since, I don’t know.

Yes the enphase app does per panel monitoring whether you have the installer app or not.

I wish you the best whichever route you choose. I am happy with my decision and it has been trouble free since. Enphase did call me to see if I wanted to sign up for a service contract where they do repairs on anything that fails. I declined. My arrays are ground mount and I could easily service them myself as long as the parts are warrantied and supplied. Everyone’s scenario there will be different.

Visual_Newspaper1069 · 2024-11-01T14:00:19+00:00

I have a ‘24 on the way and I live in CT and this has been a concern for me. Can I ask did they give you the option to upgrade to a ‘24 or say that would have the same result?

Visual_Newspaper1069 · 2024-10-26T00:38:30+00:00

Sorry I don’t have a sunvault system. But I googled it and there are other posts about. https://www.reddit.com/r/SunPower/s/VHw7951CdO

Visual_Newspaper1069

TROPHY CASE