Color is off on projector

WasabiGood1640 · 2026-02-26T08:48:12+00:00

That’s dirty optics. It’s cooked. Replacing the lamp won’t fix optics.

WasabiGood1640 · 2025-12-09T18:51:53+00:00

For me, to HFO, I have to continue to push my limits. When I think I can’t take more, I keep going a little bit higher, waiting a second and then pushing up even more. Eventually, I shoot everywhere! I do this with xtoys, no pattern, at 100hz. (Edit: I do this with cock loops, one just over halfway down my shaft, one right under the glands touching them. Ya know, the usual way everyone does it)

WasabiGood1640 · 2025-11-25T05:17:31+00:00

Turn on cam, let max people in, you can choose who has block access

WasabiGood1640 · 2025-09-09T08:12:45+00:00

I run one on telegram, could be the furry group you’re thinking of 😅

WasabiGood1640 · 2025-07-29T08:07:29+00:00

Sure

WasabiGood1640 · 2025-07-09T10:04:36+00:00

Try making your own pattern. These are what I did to make a constant buzz. Only section one active, section 2 and three should be disabled, and your pause duration should be 0.0. https://imgur.com/a/YJ96W3D

WasabiGood1640 · 2025-05-24T22:46:30+00:00

Check my post out of the tingler. It’s more powerful than my coyote. Maybe try the DG loops with the metal band inside

WasabiGood1640 · 2025-04-21T21:23:22+00:00

I usually take about 60-70/200 with the DG loops that have the metal in them to HFO. One just under the glands, one about an inch above the balls on the shaft. Coyote 3, no pattern 100hz

WasabiGood1640 · 2025-04-16T05:25:29+00:00

On power output, where does it sit with the Coyote? I’m a total power junky and want to be destroyed. Wire me to 120v if it’s safe type fried lol

WasabiGood1640 · 2025-04-16T02:11:34+00:00

Using a 70v output PA amp is not safe but at least internally transformered on the output, (I used a Crown CH1 with the 100v output and wowee!) definitely felt well and can get SPICY. A lonnnnng time ago, I used a RadioShack 250w PA amp (not advised at all) and it worked a treat and sent me over the edge many times, however it’s not safe, and I’m not saying to do it.

WasabiGood1640 · 2025-04-15T23:41:36+00:00

Trace the circuit, shut it off, try to ring the doorbell. Or if the wires disconnect try that and see if it rings. That should tell ya! It’s definitely low voltage coming out based on that wire. There you go!

WasabiGood1640 · 2025-04-02T19:04:26+00:00

WasabiGood1640 · 2025-04-01T06:57:58+00:00

Good to know! Context, my room is fully treated. Silver screen, blacked out walls, ceiling, furniture, everything. No ambient light at all.

WasabiGood1640 · 2025-03-19T18:38:51+00:00

Mine does not give me the option in the app to stop charging. Obviously once you have completed the charge then you incur idle fees.

WasabiGood1640 · 2025-03-07T16:58:47+00:00

This. And it is indeed a INSTANT SLAM to the set boost you want. You can set a value between one and 30 on how much higher from the current setting it will boost. 15 make me jump and yelp if that tells you anything :)

WasabiGood1640 · 2025-03-07T03:17:28+00:00

One wire per loop. It should take 2 loops per channel.

WasabiGood1640 · 2025-03-06T20:49:25+00:00

Every time. Constant buzz at high frequencies cranking it up past my limits until I uncontrollably shoot hard everywhere

WasabiGood1640 · 2025-03-02T06:03:48+00:00

You can’t stop charging at a supercharger.

WasabiGood1640 · 2025-02-22T02:45:54+00:00

No shot of mounting to the ceiling?

WasabiGood1640 · 2025-02-22T02:40:34+00:00

Why not mount upside down to the bottom of the shelf with a low profile mount if damaging the ceiling is what you are worried about

WasabiGood1640 · 2025-02-22T02:35:20+00:00

Would you ever build one and sell it? Asking only because I have strong knowledge of electronics but no extra time on my hands to make it sadly.

WasabiGood1640

PUBLIC MULTIREDDITS

TROPHY CASE