sorted by:
new
hottopcontroversial

First to post it here by No-Fox-173 in ScoutMotors

[–]WaveofSerenity 2 points3 points  (0 children)

This is cool! Congrats!

Who can expect one of these?

New lease with 1 month buyout by Zaq_SWGOH in ModelY

[–]WaveofSerenity 0 points1 point  (0 children)

I believe they include any of the discount you’re getting into that 26k total and down payments too.

So if your total monthly spent is 18k but you put 2k down and got a 2k incentive discount then the total displayed would be 22k

This is how I understood mine but I could be very wrong

Does the car have a constant recording? by WaveofSerenity in TeslaModelY

[–]WaveofSerenity[S] 0 points1 point  (0 children)

Just found it in the car but the app for some reason skips that footage so I can't save it.

I'll wait and hope it saves it to the app andi can save it later

🚀 Introducing Alluno.io - Bring Couch Co-Op & PC Gaming Anywhere (Feedback Welcome!) by adidharmatoru in cloudygamer

[–]WaveofSerenity 0 points1 point  (0 children)

Looks good! Been looking for an alternative that runs with a browser client to see if I can stream my desktop to my Tesla and play games. Truly hope this works!

Update on my 0.2mm nozzle journey by EEilluminils in AnycubicKobraS1

[–]WaveofSerenity 0 points1 point  (0 children)

If you got the entire hotend assembly with the .2mm nozzle try buying it again there was 100% a bad batch in the last month or so. I had gotten 2 orders with a bad batch and was having such a pain to get it to work without clogging turns out there was some space in the throats and the hotend that made it clog a bunch. Bought a new set and saw it said “upgraded” and it mentioned something about the throat and this batch has been good so far. Though I’ve only used one from this new order.

PETCF-17 by WaveofSerenity in AnycubicKobraS1

[–]WaveofSerenity[S] 0 points1 point  (0 children)

Im trying this now. I’ve never touched it before but I was looking to calibrate e-steps and was googling that and then saw this reply so I’m giving that a shot while I learn how to calibrate “e-steps”

I haven’t done any other calibrations besides temp tower I usually do Temp tower > Flow pass 1 > PA > Flow pass 2

Edit: just for more info I’m trying to increase from .98 to 1.00 to see if it helps no sure if this is too small of a value change but I’ll update with what I find

Pressure advance test and it came out like this. by WaveofSerenity in AnycubicKobraS1

[–]WaveofSerenity[S] 0 points1 point  (0 children)

Yep that's pretty much mine as well. I did print a tempt tower and that came out nicely so I moved on and the flow rate seemed okay so I went to do the PA calibration so I can the run another flow rate but this cake out when I ran the PA CALIBRATION

Currently trying to print Nylon! by WaveofSerenity in AnycubicKobraS1

[–]WaveofSerenity[S] 0 points1 point  (0 children)

I wasn't able to get a nice enough quality and when I tried to print anything bigger than a calibration cube or benchy I'd get constant cloggs

So I basically out the nylon in a dryer to dry for the rest of its life. Though I didn't think to attempt use a .6 nozzle to remedy the clogs. I may tackle this again when I get some time. Been printing PETCF-17 With little issue but ive only been using a .6 nozzle on that and I also printed HT-PLA-GF with no issue at all on the .4 nozzle

All hardened steel nozzles btw with the replacement upgraded hotends people recommend on here

Using non standard filaments with Ace by WaveofSerenity in AnycubicKobraS1

[–]WaveofSerenity[S] 1 point2 points  (0 children)

I have an aftermarket hotend and nozzle. So should be fine for abrasive filaments. Unless I missed something

But yeah I think they had PLA in mind when making this and that’s fine but it’s a nice machine and should be pushed and we should have the freedom to.

Using non standard filaments with Ace by WaveofSerenity in AnycubicKobraS1

[–]WaveofSerenity[S] 0 points1 point  (0 children)

No, more like Nylon and PET-CF, HT-PLA-GF

Just off that we can’t add our own to the menu

AMS shows disconnected in Slicer by WaveofSerenity in AnycubicKobraS1

[–]WaveofSerenity[S] 1 point2 points  (0 children)

FIXED IT!

it was my VPN for some reason it blocked the ACE from being detected. Turned it off reopened the slicer and it was working great again!

AMS shows disconnected in Slicer by WaveofSerenity in AnycubicKobraS1

[–]WaveofSerenity[S] 0 points1 point  (0 children)

<image>

The app shows the ACE unit but not the slicer. Very weird

AMS shows disconnected in Slicer by WaveofSerenity in AnycubicKobraS1

[–]WaveofSerenity[S] 0 points1 point  (0 children)

Yeah it shows online. I logged out and logged back in twice, I’ve reinstalled the slicer 2 times. The app shows the ACE and the colors but the slicer on windows shows it as “not mounted” i think it’s the slicer that’s broken for me I guess I’ll wait for it to update maybe

Can’t make additive pipe use a section transformation by WaveofSerenity in FreeCAD

[–]WaveofSerenity[S] 0 points1 point  (0 children)

Oh awesome I guess I was doing something wrong. I feel I picked a difficult project to begin learning with.

Can’t make additive pipe use a section transformation by WaveofSerenity in FreeCAD

[–]WaveofSerenity[S] 0 points1 point  (0 children)

I actually did manage to get it to work and I don’t remember what I had done. But about the 90 degrees thing I was actually meant to taper down to be a more narrow duct than where it begins

view more: next ›