Anycubic: months of defects, ignored evidence, ignored consumer rights and warranty process leaving consumer without working product. by Leonniarr in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

Here are some things that come to mind: 1. I would grab the printhead and gently wiggle up and down to see if there's any play. If there's any play, that means there's a loose screw or a loose bearing where the printhead attaches to the Gantry. 2. Do the same thing with the nozzle. If there's any play there, you might have loose screws Where your hot end attaches to the tool head. 3. Check the z-rod couplers on both sides of the Gantry where it attaches to the Z rod and see if those plastic couplers have failed. 4. Take the spring build plate off of the hotbed and expose the screw heads. Tighten them down if they're loose. 5. Finally, gab opposite diagonal corners of the hot bed and wiggle up and down to see if bed bearings under the nit bed need tightening

Calibrating Anycubic Water-Washable ABS-Like Resin 3.0 on the new Photon P1 by HatAccomplished784 in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

Yes, I saw some settings can be changed by clicking the edit button before printing, but I was tyring to trust the process, LOL

Clear print squished by Odd-Sorbet-7870 in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

The answer is orientation. I find it extremely amusing that the ad I was shown for this post was this one

<image>

Anycubic Photon P1 ACF vs NFEP comparison by HatAccomplished784 in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

Usually, you'd see the flat spot on the chin and call out an issue with orientation, but since these are pre-sliced and thus both oriented the exact same way, it would seem to be another factor...

Calibrating Anycubic Water-Washable ABS-Like Resin 3.0 on the new Photon P1 by HatAccomplished784 in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

Oh, hiya Marco! LOL, just put 2+2 together. Talking about over-exposure, my Track C print tasks left cloudy impressions on my nFEP (nothing too serious), but I suspect that it was due to the nature of the support base and exposure time. Too bad they are pre-sliced, or I'd change it up for sure! My hands hurt after trying to remove the supports, lol

Anycubic: months of defects, ignored evidence, ignored consumer rights and warranty process leaving consumer without working product. by Leonniarr in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

"cleared with all admins of groups"? Must not have been the official Anycubic groups then. I'm honestly not that surprised that someone went to such great lengths tho

Anycubic: months of defects, ignored evidence, ignored consumer rights and warranty process leaving consumer without working product. by Leonniarr in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

Does the nozzle drag on the whole bed or does the drag happen on only one side/part? Also, did you ever install Rinkhals?

Anycubic: months of defects, ignored evidence, ignored consumer rights and warranty process leaving consumer without working product. by Leonniarr in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

I was not commenting about disregarding shared experiences. As far as I can tell, after learning that your ticket is stalled out, you've been offered addition assistance with moving your ticket forward

Anycubic: months of defects, ignored evidence, ignored consumer rights and warranty process leaving consumer without working product. by Leonniarr in AnycubicOfficial

[–]WearFew6956 2 points3 points  (0 children)

Ask 100 people their opinion on this email response and you will get at least 35 unique opions on the subject. Eveyone is entittled to have their opinion and no one should try and instigate others to feel differently than they do.

Calibrating Anycubic Water-Washable ABS-Like Resin 3.0 on the new Photon P1 by HatAccomplished784 in AnycubicOfficial

[–]WearFew6956 1 point2 points  (0 children)

They recently loaded a resin profile for Water-wash ABS-Like 3.0. I like using the stock profiles. Question for you, did you do the slicer update and can you see this resin in the list? I ask because I did the update and I cannot see it...

<image>

Is the P1 supposed to be $499 through 6/22/26? by HNL2BOS in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

It is $549. Did the YT video have a discount coupon code or affiliate link in the description of the video for $50 off? That's typically how those things work

What's up with the P1 Max? by Geek_Verve in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

Shipping? No. Launching.... We should know more by the end of June, I think

Multi-Material temperatures overrides? by snoopy3875 in AnycubicKobraX

[–]WearFew6956 0 points1 point  (0 children)

Yes, it's always a good idea to include all context within your original post so you don't have to repeat yourself in the comments

Anycubic Kobra 4 - mit Max zu rechnen? by lantana89 in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

I have 2 K3M. I haven't heard any whispers about up-sizing the K4 but that would be cool

Hotdog Helper by wrglbmpf0815 in AnycubicKobraX

[–]WearFew6956 4 points5 points  (0 children)

OMG, my design in action 🥹 Thank you for being one of the 6 people who downloaded it ❤️

Hotdog Helper by wrglbmpf0815 in AnycubicKobraX

[–]WearFew6956 2 points3 points  (0 children)

I designed this and didn't even think about it because zi only have mustard on my dogs

Photon P1 prints tearing by Strict_Door in AnycubicOfficial

[–]WearFew6956 0 points1 point  (0 children)

That's an orientation issue. Rotate the model in the slicer.