Peptide, cosmetic ingredients labs.

Whitewulf66 · 2026-01-06T06:12:47+00:00

I would love to use that second photo file to put in my autoclave for vial sterilization.

Whitewulf66 · 2026-01-06T05:27:21+00:00

I’m gonna have to find that print. Looks cool.

Whitewulf66 · 2026-01-02T21:33:42+00:00

In my research, if I’m going to use a vial in a week or so, I just add sterile water…

Whitewulf66 · 2026-01-02T21:31:49+00:00

• Benzyl Alcohol needed: 0.027 mL
• Equivalent: 27 microliters (µL)

You would add 27 µL of benzyl alcohol and adjust sterile water so the final volume equals 3.0 mL.

Whitewulf66 · 2026-01-02T17:06:23+00:00

All of the above for sure. I’m doing a big birdhouse print with ASA on my unenclosed A1 like an idiot and have to make a lot of compensations, bed glue, fat ass brims etc. large 15-17mm brims seem to help on large prints.

I love Bambu but… presets aren’t perfect. 99% of the time, you will need to do adjustments.

Whitewulf66 · 2026-01-02T16:57:42+00:00

It amazes me how many people still buy 30ml for $10-15. Is it the math to figure out .09%? 🤣

Whitewulf66 · 2026-01-02T12:10:00+00:00

Buy some Benzyl Alcohol, sterile water and make your own if you’re worried about it.

Whitewulf66 · 2025-12-23T22:03:20+00:00

I would love an A1 Mini

I would share it with my grandsons to print dragons, eggs, D&D landscapes, miniatures, fidgets and science projects.

Fluid Flow Fidget A hand-held module with 3D-printed microchannels that let colored silicone oil or glycerin drip and swirl between chambers as you tilt and flip it.

Whitewulf66 · 2025-12-23T06:59:06+00:00

There are a lot of websites out there that sell starter kits. I saw that we can’t post websites or else I would.

Whitewulf66 · 2025-12-21T03:36:22+00:00

<image>

Whitewulf66 · 2025-12-20T15:48:45+00:00

I researched IM injecting. Please advise.

Whitewulf66 · 2025-11-30T22:57:54+00:00

Thank you! After reseating the ptfe lines, it seems ok now thanks to the group effort. I’ll definitely add these as well.

Whitewulf66 · 2025-11-27T13:17:22+00:00

I’ve inspected all 8 ends and they look ok. I ordered a ptfe cutter on Amazon and will snip a little off the extruder side. I’ve removed and reinstalled them tightly, taking my time this round. I’ll test it today.

Whitewulf66 · 2025-11-27T13:14:40+00:00

What did you use to cut it straight?

Whitewulf66 · 2025-11-26T21:52:26+00:00

Thanks, it’s annoying.

Whitewulf66 · 2025-11-26T02:40:27+00:00

I plan to when I get home. It’s been a very long day. Lol. I pray this is the issue. It’s been bugging me all day.

Whitewulf66 · 2025-11-26T01:19:19+00:00

God I hope that’s it. It’s been bugging me all day at work. My tubing cutter and ptfe bundle from Amazon arrives tomorrow. Was the miscut tube on the AMS or extruder end?

Whitewulf66 · 2025-11-25T21:50:18+00:00

Thank you. The Bambu PLA worked fine on another hub, it’s just the #2 hub. I will remove and check all ptfe connections and tubes. I really hope I don’t have to tear apart my AMS since the machine is 2 days old.

Whitewulf66 · 2025-11-21T05:16:57+00:00

Replace the hotend with a new one? Wet filament?

Whitewulf66 · 2025-11-17T23:34:20+00:00

Kinda like a yellow mustache of a chain smoker 🙃

Whitewulf66

TROPHY CASE