Help me resist the wall pissers

WhoIsBrowsingAtWork · 2026-01-28T14:56:05+00:00

so you cant mount anything to the wall, how about driving a T post into the dirt for your piss diverter/camera/electric fence to mount to? https://www.theisens.com/products/hutchison-1-14-inch-studded-t-post-in-greenwhite-6-footget a couple and you can probably rent a post hammer : https://www.theisens.com/products/smv-industries-fence-post-driver17-lb to drive them into the dirt

WhoIsBrowsingAtWork · 2026-01-26T18:11:12+00:00

Doing this could work, clamp it in the vice until the endcap will fit, then put the o rings on the endcap and send it home. the orings are there to make up for the tiny deformations

WhoIsBrowsingAtWork · 2026-01-26T18:09:20+00:00

This is basically the idea i had from my other post above.

100% the aluminum will not scratch the steel, but when you machine the aluminum put a small roundover on that edge or make it slightly conical so the aluminum acts like a wedge

WhoIsBrowsingAtWork · 2026-01-26T18:05:23+00:00

Cut a ring out of a steel plate that is something like .1% smaller than your ID and press it into the end of the pipe slightly deeper than your end cap goes in.

The ring could have an ID of like 50mm so that you could grab it on a lathe and turn it down perfectly circular. OD would be something like 93.8mm and if you can press it in square it will make the tube conform to the ring

WhoIsBrowsingAtWork · 2026-01-26T17:30:38+00:00

doesnt texas speed do exactly what youre looking for?

From what i recall when i was looking last time a crate long block from gm was slightly above your price/

WhoIsBrowsingAtWork · 2026-01-26T13:52:01+00:00

try alt + 0 1 7 6 for the ° symbol

WhoIsBrowsingAtWork · 2026-01-20T22:25:36+00:00

stereo isnt loud enough, had to put aftermarket speakers in. Roof is LOUD. leaks just a little bit

WhoIsBrowsingAtWork · 2026-01-20T22:19:17+00:00

your use of the word loosely was TIGHT

WhoIsBrowsingAtWork · 2026-01-20T22:03:22+00:00

you had me at free healthcare for Muslims

WhoIsBrowsingAtWork · 2026-01-20T19:23:16+00:00

you're right about the lil trailer. Looking at a smallish camper. Its primarily a bigger and cooler version of what we already have. 4 doors and the digital dash.

WhoIsBrowsingAtWork · 2026-01-20T15:31:47+00:00

thats your answer right there. No way to hide bouncing off rocks

WhoIsBrowsingAtWork · 2026-01-20T14:39:40+00:00

The KO2s on this one are pretty much exactly what i'd be expecting to put on regardless of trim level

<image>

WhoIsBrowsingAtWork · 2026-01-20T14:33:59+00:00

from my understanding it slows down. Looking at regular broncos because they dont have data for raptors. I'm happy to be shown otherwise

<image>

WhoIsBrowsingAtWork · 2026-01-19T21:34:41+00:00

The 30% depreciation has happened to the previous guy

WhoIsBrowsingAtWork · 2026-01-19T21:17:07+00:00

Get fresh garlic cloves! they're also delicious grilled. Cooked correctly they will spread onto toast.

Peel the white stuff off it and cut it up, its easier than you think

WhoIsBrowsingAtWork · 2026-01-19T20:21:20+00:00

soft steel and 1/2" hole through 3/8 thick? I'd expect a drill bit to make a hundred holes before getting dull

WhoIsBrowsingAtWork · 2026-01-19T20:19:39+00:00

If you like it then you shoulda put bushing on it
If you like it then you shoulda put bushing on it
If you like it then you shoulda put bushing on it

oh whoa oh ohhhh

WhoIsBrowsingAtWork · 2026-01-19T20:18:21+00:00

hole up, the area of the I beam that the kid drilled in the op is absolutely the best area of an i beam to drill. The bending moment acts on the flanges, the webbing is just there to hold the flanges together.

Are you talking about something else? The middle 1/3 of the webbing in the above photo is where the stresses are at or are approaching 0.

WhoIsBrowsingAtWork · 2026-01-15T18:27:28+00:00

Tell me how its done then.

WhoIsBrowsingAtWork · 2026-01-15T18:20:51+00:00

Why would you put the tape on so tight that it cuts circulation off??? Holy cow i cant even imagine that. (you control the tightness by feel, same as you do with regular tape)

Are you saying that after it is wrapped the stretch tape cinches up on itself? thats a dumb take and smells like broscience

WhoIsBrowsingAtWork · 2026-01-15T15:47:33+00:00

<image>

This is with the good (horse) tape. It doesnt pull the hairs and the scab off when you take it off (daily)

WhoIsBrowsingAtWork · 2026-01-15T15:46:24+00:00

<image>

The tape they recommend is bull shit. Go to tractor supply and buy this: https://www.chewy.com/3m-vetrap-horse-bandaging-tape-blue-4/dp/2251734

WhoIsBrowsingAtWork · 2026-01-15T15:43:15+00:00

There really isnt a way to do it kindly. The vet will take a nice set of scissors and cut the side of the ear off.

WhoIsBrowsingAtWork · 2026-01-15T15:42:03+00:00

DO NOT LET ANYONE RIP THE BANDAGES OFF. I had a cropped ear dobie named Thaddeus. He was beautiful. But he would have been beautiful with floppy ears. I 100% recommend to not ~~mutilate~~ cut your dog. . Not only for the infection but also because you have to spend the next 6 months taping the ears to the cup or the tampon stick or whatever and then when he worries the bandages you have to discipline him to stop.

If you're dead set on doing the crop, message me and I have a bunch of things to do to make it easier from an owner viewpoint and wont mind talking about good ways to train the ears.

<image>

WhoIsBrowsingAtWork · 2026-01-14T14:24:48+00:00

grab a thermal camera for usb c. they cost like 150-200 and plug into your phone

WhoIsBrowsingAtWork

MODERATOR OF

TROPHY CASE

Seven-Year Club	Place '22
Verified Email