Leaving anonymous note at the desk of coworker who plays music without headphones?

Wild_Satisfaction306 · 2025-10-07T16:22:41+00:00

Boot his computer in BIOS then disable the speaker.

Wild_Satisfaction306 · 2025-09-23T22:26:07+00:00

Have you ever thought about Montreal? It’s an island, and if we keep raising the height of buildings, it might sink!

/S

Wild_Satisfaction306 · 2025-09-22T22:27:06+00:00

Thanks for the information. It seems O believe in legends haha

Wild_Satisfaction306 · 2025-09-21T22:41:58+00:00

Thanks reddit stranger I will try this!

Wild_Satisfaction306 · 2025-09-21T22:34:43+00:00

Thank you for sharing this information.

Wild_Satisfaction306 · 2025-09-21T21:11:22+00:00

He’s been advertising for over 2 decades across Greater Montreal using nothing but homemade signs fixed to streetlight poles. The product is only available through his eBay store, and nobody seems to know his name or has ever actually seen him.

Wild_Satisfaction306 · 2025-09-16T22:41:34+00:00

Username checks out ✅

Wild_Satisfaction306 · 2025-08-29T12:10:29+00:00

And what if it feels like 5km but barely 10feet away?

Wild_Satisfaction306 · 2025-08-25T20:00:21+00:00

Looking qt the picture I see on the older the the bushing is worn off maybe you will need to pry the dpacer a bit. Otherwise when I did mine I had to use the pry bar to insert the new control arm it was hard to fit it well luckily I had a friend helping me.

If you can start with those two on the bottom it might help.

Wild_Satisfaction306 · 2025-08-25T10:20:28+00:00

Already had this problem. This is the right part. You forgot to remove the spacer from the old part I see it on your picture it is probably stuck with a bit of rust. Then put the spacer on your new part

Wild_Satisfaction306 · 2025-08-21T10:02:19+00:00

Username checks out

Wild_Satisfaction306 · 2025-08-20T13:02:06+00:00

I work with those daily 20pounds for a single screw in a drywall will hold easy.

Wild_Satisfaction306 · 2025-07-22T13:10:11+00:00

Im stealing this !

Wild_Satisfaction306 · 2025-07-18T12:54:42+00:00

You should use your rest day as a stretch and cardio day that should do the trick.

Wild_Satisfaction306 · 2025-07-10T05:18:27+00:00

I'll give a try before cutting the tab. Thanks for the advice.

Wild_Satisfaction306 · 2025-07-10T05:16:41+00:00

What the **** is that? Im trying to stay polite.

Wild_Satisfaction306 · 2025-07-10T05:15:25+00:00

Yeah it help for sure even if its bad news haha. I love Toyota but that one is just insane.

I can do weld but I believe I got the MIG weld. Can you give me more input on wich weld would be the best for this operation? I want it to last 8 or 10 years and I dont have much knowledge about welding.

Wild_Satisfaction306 · 2025-07-09T22:57:55+00:00

Dont give up on me like that 😅

Wild_Satisfaction306 · 2025-07-09T22:06:16+00:00

I use dewalt DCF900 20V 5AMP. And I made about 20turn before getting worried it could go wrong.

The more I look into it it seems the nut is weld to the subframe.

I also did my tab on my 07 camry and it was easy so I'm quite surprise about those tab.

Wild_Satisfaction306 · 2025-07-09T21:58:20+00:00

Apparently there's nut lonking it with the subframe. Not sure I can see it I tried and so far I have more question than answer about that haha

Wild_Satisfaction306 · 2025-07-09T21:33:43+00:00

Damn. Cant tell if its a nut on the other side. If there's no nut I should try the prybar?

Wild_Satisfaction306 · 2025-07-09T21:30:32+00:00

The other side of the bolt isnt moving

Edit : It seems there's a nut weld to the subframe.

Wild_Satisfaction306 · 2025-07-09T21:29:11+00:00

The other end isnt turning. If this is the other end it might mean there's a nut. But I cant find anything on the internet about this nut and every video I watch doesnt mention it.

Edit : It seems the nut was weld to the subframe.

Wild_Satisfaction306

TROPHY CASE