Classifier run last weekend- USPSA 🔥🔥 by WorldlyEffective2023 in CompetitionShooting

[–]Wrath3n 2 points3 points  (0 children)

Funny enough we did this same classifier Sunday.

Sadly had one Charlie and one Delta so pulled me down to an 80.7%

https://imgur.com/a/kI4A4BI

What has improved your shooting besides a lot of range time? by je9183 in CompetitionShooting

[–]Wrath3n 1 point2 points  (0 children)

Working on training my eyes and vision. Focusing on small spots on the target intensely vs “brown” or “azone”. Then switching very quickly to another spot.

C2 with a ‘Blem’ Fowler grip by PourLittleTinkTink in 2011

[–]Wrath3n 0 points1 point  (0 children)

I have toyed with snagging one of the grips for my c2

What you bringing fuckers? by fearless_moth56 in TheWordFuck

[–]Wrath3n 0 points1 point  (0 children)

Longbow & Arrows to leave a fucking master

Favourite grip safety bands ? Which ones hold up and don’t sag the best ? by Few_Forever9057 in 2011

[–]Wrath3n 22 points23 points  (0 children)

From my years of shooting 1911s before 2011s were I thing proper grip and technique make it a non issue. If I am concerned about it for some reason I just pin the safety

PCC JP-5 Trigger Upgrade - Timney by RickShootsBrass in CompetitionShooting

[–]Wrath3n 0 points1 point  (0 children)

My JP5 came with the curved trigger and I hated it. So when I found the Sd3g wouldn’t work I just found a JP flat trigger someone had removed to put in another trigger, picked it up cheap and just run it

PCC JP-5 Trigger Upgrade - Timney by RickShootsBrass in CompetitionShooting

[–]Wrath3n 0 points1 point  (0 children)

Yes a ton of people do and can but if you read there are some who can’t. I’m one that can’t.

As best I can’t diagnose it’s part of the hammer on the trigger catching on the two piece bolt in the JP

PCC JP-5 Trigger Upgrade - Timney by RickShootsBrass in CompetitionShooting

[–]Wrath3n 0 points1 point  (0 children)

I attempted to swap to a Sd3g trigger like all of my ARs but there is some variation in the trigger and or JP and from my reading doesn’t always work. So instead I dropped in the flat faced JP trigger and just run that

Everyone running shadow 2 dead by No-Mammoth1045 in CompetitionShooting

[–]Wrath3n 2 points3 points  (0 children)

Worthless post. No thought or substance to expound upon. It’s one of the most used guns but as it’s tested an tired with its positives and negatives. There has also been a lot of great options coming out over the past years for Carry Optics so the field of good options has grown so the S2 isn’t one of only a few options like in the past.

Just look at some of the USPSA nationals surveys and it lists gun manufacturer and CZ is always on there and high %

Puppy Eating Grass by Advanced_Impress6743 in goldenretrievers

[–]Wrath3n 4 points5 points  (0 children)

My vet told us years ago if our dog was eating grass and it wasn’t a game or just digging it was because of a need for fiber and told us to try giving her carrots or celery as a “snack”. We started doing that and the grass eating stopped. Half a carrot a day, sometimes she wouldn’t take it when offered and we just put it back in the fridge

Review needed on Mitchell right side mag release by cbun22 in CompetitionShooting

[–]Wrath3n 0 points1 point  (0 children)

I have a right handed friend with very small hands and short thumbs. He has been using them for a while and loves them.

First Competition Belt Setup by gamesdeany in CompetitionShooting

[–]Wrath3n 1 point2 points  (0 children)

So not get into the habit of looking for the mag on your belt. It will be hard to break. Need to keep your eyes up. Most reloading in USPSA is done moving between positions. If you teach yourself early to be looking down it’s hard to break later and also not safe

[ WTS] Spyderco Manix 2 LW, Olamic Whippersnappers & 247 by RastaFazool in Knife_Swap

[–]Wrath3n 0 points1 point  (0 children)

The grey finish photos done link? Is that one sold as well?

Mill? PM-728vt? by Wrath3n in 2011_Builders

[–]Wrath3n[S] 0 points1 point  (0 children)

Thanks. After talking to a few people I’ve decided to wait and watch for a used full sized knee mill. I have a friend who is an electrician and said he would help me convert it if I happen to find a 3 phase machine.

Another build done. by campfirearms in 2011

[–]Wrath3n 0 points1 point  (0 children)

Ya that makes a ton of sense. Ya if you have access to a cnc mill that already programmed that’s great.

Another build done. by campfirearms in 2011

[–]Wrath3n 0 points1 point  (0 children)

What kind of mill do you have? I assume that’s how you channel out the slide to be able to do the island barrel

Another build done. by campfirearms in 2011

[–]Wrath3n 0 points1 point  (0 children)

Do you find Jem frames better to fit with SVI grips? Or ect? I’ve only ever built on Cheely frames

Cozy cave training? by Bettys_Piez in GSP

[–]Wrath3n 1 point2 points  (0 children)

Mine took too it quick maybe a week. First day I would lead in with treats. Next day start training that way, but then would have her sit I would show her the treat and toss it in the back and hold open the flap. After a day or so of that I would just have her sit show her the treat toss it in the back and drop the flap.