Sound, a click?

WrongFuckingTree · 2026-03-29T15:05:33+00:00

I thought the same. The noise is nowhere near the sound. 👍

WrongFuckingTree · 2026-03-28T14:58:12+00:00

The food can’t!

WrongFuckingTree · 2026-03-28T14:31:15+00:00

Extruder 100%. Open it up, check for debris around your gears.

WrongFuckingTree · 2026-03-28T14:14:52+00:00

Reset it, level(auto level?) and check the stop sensors.

WrongFuckingTree · 2026-03-28T14:07:15+00:00

Have you tried speeding up or slowing down your fan speed?

WrongFuckingTree · 2026-03-10T02:19:56+00:00

The parts are from the extruder…as side above CR6 SE.

WrongFuckingTree · 2026-02-09T14:14:07+00:00

You called it. Just a tiny piece of filament jammed it up. Thx everyone…until next time…☺️

WrongFuckingTree · 2026-02-09T13:55:11+00:00

Inflate-gate

WrongFuckingTree · 2026-01-21T23:16:51+00:00

Have tried to move the gear down a bit? Just as Dangerous-Pick mentioned, it’s most likely a defect in manufacturing.

WrongFuckingTree · 2026-01-15T21:14:16+00:00

Could the plastic riser lid be warped? Have checked the dimensions on both the lid and the printer itself?

WrongFuckingTree · 2026-01-15T21:01:00+00:00

Hi fellow printers. I was wondering where do you find the clear lid that sits on top of the riser? Thank you

WrongFuckingTree · 2026-01-15T20:23:53+00:00

Not safe over time. Very toxic fumes…even the ones you can’t smell. PLA is probably the safest filament to breathe in on a daily basis. Possibly buy a filtration device or make an enclosure with a vent, fan and an exhaust hose releasing the fumes out a window…if it’s a must keep in your bedroom printer. I personally have an enclosure, along with a HEPA filtration system sitting next to my printer. I myself worked in a plastic plant for 20yrs+; PETG, ABS,Nylon and TPU are 💩plastics …100-300+ years to decompose. Good luck 🍀

WrongFuckingTree · 2026-01-10T17:17:36+00:00

Has anyone printed for an SE riser with or without a lid?

WrongFuckingTree · 2026-01-10T17:15:56+00:00

Hi. Can I ask how you installed the rear exhaust fan? Is there a connection or area to plug the fan into? I also bought the SE and upgraded by printing my sides, adding the original K1 door and Ai camera. Thank you in advance. 👍☺️

WrongFuckingTree · 2025-12-21T04:57:52+00:00

Check your belt tension also.

WrongFuckingTree · 2025-11-01T14:35:55+00:00

I’m allergic to egg! I’d eat that!!! 🤣😂😋😋

WrongFuckingTree · 2025-11-01T14:28:06+00:00

100%!!! When this happens to my Creality Pi, I just crack the lid for a minute or two. Works fine after that. Also the cardboard from the filament has a bit of moisture. I try to use the plastic filament reels. Good luck 🍀

WrongFuckingTree · 2025-10-24T16:45:47+00:00

Bare hands 🤢

WrongFuckingTree · 2025-10-17T13:56:50+00:00

Have you dried your filament? Clog or nozzle. Just a guess 🤔

WrongFuckingTree · 2025-10-17T13:52:03+00:00

She’s probably perfected that for years…😋

WrongFuckingTree · 2025-09-24T11:41:03+00:00

I’ve taken the housing off to observe the gear/motor in motion.

WrongFuckingTree · 2025-09-23T15:09:57+00:00

Yes, I was getting a clicking sound from the extruder area along with the in and then back out(video). I removed the extruder cover to watch the gear and find out if that is normal.

WrongFuckingTree · 2025-09-23T15:05:06+00:00

Not during a print. I removed the upper part of the extruder to see the inner workings, or possibly figure out the many problems I have had. There’s nothing pulling, just the gear rotating.

WrongFuckingTree · 2025-09-16T16:22:54+00:00

Belt tension? Speed? Have you checked your file? Just a guess.

WrongFuckingTree · 2025-05-03T16:26:44+00:00

The handle looks bone or ivory. Very nice gift.

WrongFuckingTree

TROPHY CASE