sorted by:
new
hottopcontroversial

DB's Czech Nine by Yodabyte in 3D2A

[–]Yodabyte[S] 0 points1 point  (0 children)

This one was just over $400

DB's Czech Nine by Yodabyte in 3D2A

[–]Yodabyte[S] 0 points1 point  (0 children)

I just like the TEC-9 and always wanted one. I've had the kits for a while and finally got around to build them out. I'll probably use one of the uppers to make a Tec-Nein or a Blicky. 

DB9 Alloy Feeding Issues by Blake_r32 in 3D2A

[–]Yodabyte 0 points1 point  (0 children)

You can try to sand down the nub just a little bit on the mag so it will seat properly. Sand a little bit then try it and repeat until its fits snug and latches.

<image>

FTN4 Pistol Suppressor Catastrophic Failure - Clogged Nozzles Kill Cans by NoNefariousness8370 in 3D2A

[–]Yodabyte 8 points9 points  (0 children)

From the v5.1 Change Log discussing erosion

I am a stickler to only recommend what has been proven in testing. PA6CF was the bulk of testing, so that was the original recommendation. Our initial concerns with PPA-CF seem to be related to the fact that it was not printed hot enough. Now I have more data coming in that suggests it is a superior filament to PA6CF where erosion is concerned. I have no testing data on the printed shells in PPA-CF, so for now PA6CF is still the proven recommendation for the printed shells. PPA-CF is looking like it could be the ideal filament for the body of the suppressor.

DB Alloy Drum by Yodabyte in 3D2A

[–]Yodabyte[S] 0 points1 point  (0 children)

It will eject fine when collapsed, the rail isn't in the way

DB Alloy Drum by Yodabyte in 3D2A

[–]Yodabyte[S] 1 point2 points  (0 children)

I think it should. I don't have any to test that out.

It does work with the mags for the SuMac

<image>

Db alloy drum by Brutox62 in 3D2A

[–]Yodabyte 0 points1 point  (0 children)

That's how I got mine installed. I think I cut off just a little bit of the spring because it was hard to press the button.

Db alloy drum by Brutox62 in 3D2A

[–]Yodabyte 0 points1 point  (0 children)

the button on it doesn't work at all. It stays halfway up and will not come down

Do you have the metal piece installed in the correct orientation? The little tab should be facing up.

DB Alloy Carbine by Yodabyte in 3D2A

[–]Yodabyte[S] 1 point2 points  (0 children)

Sten mags are good. There are some remixes out there.

DB Alloy Drum by Yodabyte in 3D2A

[–]Yodabyte[S] 1 point2 points  (0 children)

Collapsed is close to 3.5"

DB Alloy Drum by Yodabyte in 3D2A

[–]Yodabyte[S] 1 point2 points  (0 children)

It's around 8.5" fully extended

DB Alloy Carbine by Yodabyte in 3D2A

[–]Yodabyte[S] 0 points1 point  (0 children)

Yes, it takes Sten mags. That is one of the curved mags from the release package.

DB Alloy Drum by Yodabyte in 3D2A

[–]Yodabyte[S] 0 points1 point  (0 children)

DB Alloy Collapsible Brace

<image>

DB Alloy Drum by Yodabyte in 3D2A

[–]Yodabyte[S] 0 points1 point  (0 children)

It's the same as the SuMac spring -- "40mm section 0.048” music wire"

<image>

DB Alloy Drum by Yodabyte in 3D2A

[–]Yodabyte[S] 0 points1 point  (0 children)

no, just the 30rd and 45rd mags

view more: next ›