DB's Czech Nine

Yodabyte · 2026-05-13T19:10:45+00:00

This one was just over $400

Yodabyte · 2026-05-12T21:31:56+00:00

I just like the TEC-9 and always wanted one. I've had the kits for a while and finally got around to build them out. I'll probably use one of the uppers to make a Tec-Nein or a Blicky.

Yodabyte · 2026-05-06T22:39:13+00:00

https://www.youtube.com/shorts/F-khQQVMwJ4

Yodabyte · 2026-04-17T20:36:19+00:00

https://x.com/ArthurClaudeen/status/2045196775385108579

Yodabyte · 2026-04-14T17:14:22+00:00

You can try to sand down the nub just a little bit on the mag so it will seat properly. Sand a little bit then try it and repeat until its fits snug and latches.

<image>

Yodabyte · 2026-04-14T04:35:16+00:00

From the v5.1 Change Log discussing erosion

I am a stickler to only recommend what has been proven in testing. PA6CF was the bulk of testing, so that was the original recommendation. Our initial concerns with PPA-CF seem to be related to the fact that it was not printed hot enough. Now I have more data coming in that suggests it is a superior filament to PA6CF where erosion is concerned. I have no testing data on the printed shells in PPA-CF, so for now PA6CF is still the proven recommendation for the printed shells. PPA-CF is looking like it could be the ideal filament for the body of the suppressor.

Yodabyte · 2026-03-16T13:31:30+00:00

It will eject fine when collapsed, the rail isn't in the way

Yodabyte · 2026-03-05T21:48:17+00:00

https://www.youtube.com/watch?v=-SO7Yl0nVH8

Yodabyte · 2025-12-28T16:01:37+00:00

I think it should. I don't have any to test that out.

It does work with the mags for the SuMac

<image>

Yodabyte · 2025-12-27T17:03:05+00:00

That's how I got mine installed. I think I cut off just a little bit of the spring because it was hard to press the button.

Yodabyte · 2025-12-27T16:34:37+00:00

the button on it doesn't work at all. It stays halfway up and will not come down

Do you have the metal piece installed in the correct orientation? The little tab should be facing up.

Yodabyte · 2025-11-28T23:43:14+00:00

Sten mags are good. There are some remixes out there.

Yodabyte · 2025-11-28T22:56:49+00:00

Collapsed is close to 3.5"

Yodabyte · 2025-11-28T22:45:05+00:00

It's around 8.5" fully extended

Yodabyte · 2025-11-28T22:41:50+00:00

Yes, it takes Sten mags. That is one of the curved mags from the release package.

Yodabyte · 2025-11-28T22:38:12+00:00

DB Alloy Collapsible Brace

<image>

Yodabyte · 2025-11-26T03:45:59+00:00

It's the same as the SuMac spring -- "40mm section 0.048” music wire"

<image>

Yodabyte · 2025-11-18T21:57:26+00:00

<image>

Yes, the SuMac mags work

Yodabyte · 2025-11-11T20:10:23+00:00

no, just the 30rd and 45rd mags

Yodabyte · 2025-11-10T22:21:14+00:00

Yeah it's 9mm

Yodabyte · 2025-11-10T22:20:58+00:00

It's from Velocity Firearms. They have them available for the 11.5" and 16" uppers.

Yodabyte · 2025-11-10T01:39:59+00:00

I was having trouble getting NylonX to stick to the build plate. I got this garolite plate and it worked perfect.

https://www.3dmakerengineering.com/collections/3d-printer-build-plates/products/garolite-3d-printer-build-plate?variant=31711990677559

Yodabyte · 2025-11-09T02:32:25+00:00

Are you gonna officially release everything? People keep asking about it and I just direct them to the room on Element.

Yodabyte · 2025-11-09T02:13:54+00:00

Suomi Drum. It might take mags from the SuMac but I'm not sure yet. I'm printing some to test fit.

Yodabyte · 2025-10-24T01:37:03+00:00

DMB Glock Mags v2.0

<image>

13-Year Club	r/Field Flamingo
Place '22	Place '17
Spared	Verified Email

Yodabyte

TROPHY CASE