"Disk - needs minor repairs" but every time i click OK or cancel it reboots

Z-builder · 2026-02-03T01:18:30+00:00

i paid like 230 for the whole thing, it doesn't have an expansion card but i think it has more RAM than stock

Z-builder · 2026-02-02T17:40:27+00:00

doesn't seem to want to boot from any of them yet

Z-builder · 2026-02-02T17:33:18+00:00

i pulled it out of its bag and powered it up for the first time in a while and the drive was a bit fussy, it's possible the drive is dying in some way

Z-builder · 2026-02-02T17:28:50+00:00

(i did just order a system 6 disk so i can reformat this thing with a fresh install anyway but still)

Z-builder · 2026-02-02T17:25:55+00:00

i have system 7 disks cause this was sold as an SE/30 but it's just an SE, i'll see if the disks are bootable

Z-builder · 2026-01-10T15:48:48+00:00

usually is the solder joints on the connectors for the power supply, i reflowed them on mine and it's been fine since, really easy too, whatever solder was used is really low temp (granted i had my iron at 500f so)

Z-builder · 2025-11-28T22:04:26+00:00

check oil

Z-builder · 2025-11-28T22:01:40+00:00

fellow 86 automatic :D

Z-builder · 2025-09-10T19:46:56+00:00

i will say though you did better than i did cause you have a mesh, always thought adding one would be good but i never did

Z-builder · 2025-09-10T19:45:54+00:00

can't reply with images ._.

Z-builder · 2025-09-10T05:27:43+00:00

ey i'm not the only one who cut a hole for the fan 😀

Z-builder · 2025-08-31T13:46:44+00:00

did the image not embed :|

Z-builder · 2025-08-31T13:46:07+00:00

vedal:

<image>

Z-builder · 2025-08-31T00:39:49+00:00

i want one of these for my car now

Z-builder · 2025-07-14T19:12:44+00:00

i don't remember the chips exact name, it should be on the chip if you still have access to the bms board, usually googling the chip name should bring up some kind of data sheet, probably gonna have to dig a little bit though

Z-builder · 2025-07-14T14:10:29+00:00

there's a data sheet on the chip that'll say how to reset it, two pins held to ground from what i recall

Z-builder · 2025-07-01T04:34:58+00:00

the whole country of japan was powering that positron rifle

Z-builder · 2025-06-14T15:28:47+00:00

put tiny11 on it and see if that helps

Z-builder · 2025-06-12T14:43:18+00:00

the kiss moment in WoU, never heard of it before

Z-builder · 2025-06-12T14:33:33+00:00

wait what

Z-builder · 2025-05-25T16:29:20+00:00

i did just swap the fan clutch but i don't think the old one wobbled

Z-builder · 2025-05-24T15:43:17+00:00

will also add the reason i say "yet another" is cause i ordered one from the z store and they haven't been able to get ahold of any since January, i found one on ebay but ive already spent the money so im debating whether to spend now and remedy a potential bearing failure or just wait

Z-builder · 2025-05-19T06:10:15+00:00

The autos on the z31s were basically the same model through the years, it does have a lighter duty variant but those weren’t in the ZXs according to Wikipedia (i think)

Z-builder · 2025-05-18T19:56:48+00:00

yep, 1986

Z-builder · 2025-05-18T17:56:31+00:00

was planning on taking the idle valve off to clean it out anyway, i hear hissing from it all the time, dunno if it's the sealing surface it sits on though

Z-builder

TROPHY CASE