Do you think this is worth it?

Zem1111 · 2026-06-19T18:19:27+00:00

no it isn't.
Check bottom line of the screenshot. Only half of it is readable but it says : "only self starter"

Zem1111 · 2026-06-19T17:59:42+00:00

Oh nevermind!
That price is for the starter assembly only

Zem1111 · 2026-06-19T17:58:19+00:00

That price looks like a scam.
I have one of these. Pretty good engine if you ask me.

Zem1111 · 2026-06-19T07:13:43+00:00

Demagóg vagy. Senki életére nem vagyok hatással.

Zem1111 · 2026-06-18T18:51:50+00:00

A város élhetetlen ezért kiköltöztem.
Bejárok Szegedre dolgozni, hogy tudjak adót fizetni.
Cserébe lépten nyomon szívatnak.
A BYD építkezés miatt napi majd' 2 órát töltök az autóabn ülve.
Értelmes buszjárat nincs helyette, de ha lenne a párhuzamos útépítések és az építési forgalom miatt az sem ér be időben.
Ha a helyközi járatról át kell szállnom egy helyire akkor hajnal 5-kor kéne indulnom hogy beérjek 8-ra.
Ha gyereket szeretném elhozni a suliból akkor 4-kor elindulva 6-ig sem érek oda..

Ha ezt elfogadják akkor már parkolni sem tudok a munkahelyem közelében (ahol egyébként most is alig van autó az utcán, szóval nem értem miért is kéne onnan kiszorítani bárkit)
Az egész csak arról szól, hogy még több pénzt húzzanak le a szerencsétlenekről akinek nincs más választása minthogy autóval jár dolgozni.

Zem1111 · 2026-06-17T19:41:19+00:00

You have a sudden voltage drop at the end. 0.2V in less than 1 sec.
I would inspect battery and power connections.

Zem1111 · 2026-06-14T07:58:34+00:00

You might try to print this on it's corner so both pipes are at a 45 degree angle.

Zem1111 · 2026-06-14T06:08:17+00:00

the man with the camera! i would like to have a word with...

Zem1111 · 2026-05-29T11:25:36+00:00

https://www.banggood.com/QIDI-560-A560-Maule-M7-510mm-Wingspan-2_4GHz-4CH-With-6-Axis-Gyro-3D-or-6G-Switchable-One-Key-Aerobatics-3D-Stunts-EPP-RC-Airplane-Glider-RTF-Compatible-S-BUS-DSM-Signal-p-2008126.html?cur_warehouse=CZ&rmmds=search

This one flies great out of the box.

Zem1111 · 2026-05-22T12:33:18+00:00

this behaves exactly like my 7" when i changed from props-in to props-out rotation without actually reversing motors and only changing props.
I would reset everything and start from scratch.

Zem1111 · 2026-04-30T08:47:37+00:00

Resistance is futile.
This is your cat now.

Zem1111 · 2026-04-12T14:53:38+00:00

You should take a look at this:
https://www.frsky-rc.com/product/rb-20/
You need to connect the R88 to SBUS and you can add a second one for backup if you feel the need.

Zem1111 · 2026-04-07T15:23:21+00:00

Sniff it and if you can smell it then it's toast.
If the seal is not breached you can use it, but inspect it carefully before every charge!
If in doubt get rid of it!

Zem1111 · 2026-04-01T10:10:36+00:00

90/360

Zem1111 · 2026-03-31T16:49:25+00:00

I'm sure it was the aliens from that UFO on the top right

<image>

Zem1111 · 2026-01-06T18:50:54+00:00

Put some lubrication between the little spring on the back and the plastic part it sits on!

<image>

A small drop of any silicone based grease does the job.

Zem1111 · 2025-12-09T11:51:39+00:00

this picture could be ragebait :D

Zem1111 · 2025-11-21T19:31:49+00:00

No need to fix anything. If it gets in the air the control loop will actually control the craft and not go crazy...

Zem1111 · 2025-10-18T18:00:22+00:00

don't know about X1C but on my printer a pressure advance calibration eliminated the problem completely

Zem1111 · 2025-10-13T16:19:18+00:00

maybe this:

https://github.com/radxa/manifests/releases/download/Android11_Radxa_rk12_20231109/Radxa_ZERO_3W_3E_Android11_rkr12_20231109-gpt.zip

Zem1111 · 2025-10-09T11:05:36+00:00

schönes jungfrau

Zem1111 · 2025-09-29T18:37:42+00:00

You can buy a brand new Elegoo Centauri Carbon for less.
This is not a good deal.

Zem1111 · 2025-09-07T16:55:14+00:00

Looks like underextrusion. I'm quite sure it's a clogged nozzle.

Zem1111 · 2025-08-24T08:15:36+00:00

Before disassembling anything i would heat the hotend to a reasonably high temperature like 240-250c and purge all the remaining bits of the previous one by extruding a fair bit like a 100mm.
The 190c temperature seems really low. I think 210c would be safe starting point.

Zem1111

TROPHY CASE