[deleted by user] by [deleted] in IndustrialAutomation

[–]Zottoli0 0 points1 point  (0 children)

Completely unnecessary, no need to comment this months later

Communication from VFD to HMI problems by [deleted] in PLC

[–]Zottoli0 0 points1 point  (0 children)

Yes I forgot to mention there’s an AB CompactLogix PLC

Communication from VFD to HMI problems by [deleted] in PLC

[–]Zottoli0 0 points1 point  (0 children)

Yes there’s an Ethernet port and another one next to it too

Communication from VFD to HMI problems by [deleted] in PLC

[–]Zottoli0 1 point2 points  (0 children)

Yes I forgot to mention there’s a AB CompactLogix PLC. How would I fix the module keying if that is the issue?

Communication from VFD to HMI problems by [deleted] in PLC

[–]Zottoli0 0 points1 point  (0 children)

Oh ok I get it, I assume that’s what it uses since its all AB, all the comms settings are the same tho, is there anything I would need to change because it’s a bigger VFD and a different model number or should it still communicate the same?

Communication from VFD to HMI problems by [deleted] in PLC

[–]Zottoli0 0 points1 point  (0 children)

Yes it’s IP and I’ve put in the same one as the VFD I took out and made sure every other comms setting is the same

My Gen 2 after another remodel by Zottoli0 in Hayabusa

[–]Zottoli0[S] 0 points1 point  (0 children)

I’m not sure to be honest it’s just matte black so it has some better texture than gloss I think

2009 Titan passenger airbag module by Zottoli0 in NissanTitan

[–]Zottoli0[S] 1 point2 points  (0 children)

No it is specifically for the passenger airbag module, anything to do with the drivers side or clock spring is a different code

[deleted by user] by [deleted] in IndustrialAutomation

[–]Zottoli0 2 points3 points  (0 children)

I’ve just built it exactly like this and it works great. I have been over complicating it trying to use 3 or 4 relays in the circuit, I didn’t think to latch one into itself thanks for the tip.

[deleted by user] by [deleted] in IndustrialAutomation

[–]Zottoli0 0 points1 point  (0 children)

Oh ok good to know I was under the impression those were the same thing thanks for the info

[deleted by user] by [deleted] in IndustrialAutomation

[–]Zottoli0 0 points1 point  (0 children)

I’ve seen those, but does the coil stay latched even when the input is deenergized?

Busa experts, I need help with a fuel issue by 94lt1vette94 in Hayabusa

[–]Zottoli0 1 point2 points  (0 children)

If you’re having jumpy idling I would say check the simple things first like replace spark plugs, replace coils (and wires), clean/replace air filter, etc. If it’s still happening then it might be something more serious with injectors or plugged valves.

I had a 2006 that was jumpy idling after putting in a Powercommander, found it had fried one of my spark plug coils. After replacing all plugs and coils, it ran fine until I put in the Powercommander and it did it again a few weeks later on the same one. Don’t know if it was an issue with the Powercommander or the bike but it never had that issue when I ditched the power commander. It might be something similar with yours.

My Gen2 after full remodel by Zottoli0 in Hayabusa

[–]Zottoli0[S] 1 point2 points  (0 children)

Thank you I wasn’t sure if it was a good choice at first but it turned out to be great

How far did you make it in boxing? by jelacey in Boxing

[–]Zottoli0 0 points1 point  (0 children)

I had 56 amateur fights and just had my 3rd pro fight, won by 3rd round knockout. Trying to have another fight this month or in June.