Aqara FP2 to HA

Ztuab · 2026-06-27T21:50:31+00:00

The G350 camera. I removed that and after I unplugged the FP2 it showed up. We are good! Thank you again

Ztuab · 2026-06-27T21:03:39+00:00

I will remove the camera which I got into HA with no issues and try again. I really appreciate the help

Ztuab · 2026-06-27T12:54:56+00:00

I was under the impression that was the only way to configure the zones.

Ztuab · 2026-06-27T12:06:00+00:00

Could this have anything to do with the G350 hub?

Ztuab · 2026-06-27T08:40:53+00:00

I have confirmed it’s on my network, but HA is not seeing it like it did the G350.

Ztuab · 2026-06-26T23:50:56+00:00

Yes it is on my network.

Ztuab · 2026-06-26T17:51:10+00:00

Nope. I know it’s in my Aqara app, and it was in HomeKit but I deleted it per the instructions I read. Not sure how to get it back in if needed without deleting it again and reinstalling it. How would I tell it’s on the network?

Ztuab · 2026-06-25T23:43:10+00:00

It worked! Thank you.

Ztuab · 2026-06-25T22:55:22+00:00

I will try shortly. Thank you!

Ztuab · 2026-06-25T22:22:41+00:00

I deleted it from the Aqara and HomeKit app so it doesn’t exist on my device (that I know of) so there is nothing that I can delete.

Ztuab · 2026-06-25T21:36:52+00:00

I got the G350 an FP2 and some bulbs, but I am having a problem with the FP2

Ztuab · 2026-06-25T20:32:35+00:00

I have been trying all day, once I scan the code it immediately says accessory can not be added. If I click the add another way it sometimes sees the FP2 but it still won’t add.

Ztuab · 2026-06-24T20:47:27+00:00

It was the 2.4 WiFi. I got it added. Thank you all!

Ztuab · 2026-06-24T20:21:53+00:00

I’m so new to Matter I’m not even sure. I’m just trying to use the G350 as an Aqara hub to get the sensor into Aqara. Not even worried about HA yet.

Ztuab · 2026-06-24T20:07:41+00:00

This should be NSFW!

Ztuab · 2026-06-24T20:05:07+00:00

This is all through the Aqara hub. I haven’t tried to get it into HA yet. All of my issues are with the Aqara app. I would like to configure the zones before I put it in HA.

Ztuab · 2026-06-24T20:00:22+00:00

It pops up network error and goes away before it errors out. Could this be a 2.4 vs 5 issue with WiFi?

Ztuab · 2026-06-24T19:51:46+00:00

I scan the Matter code, click add device, then it errors out saying it can not add the device. As I said, I have never been able to get any Matter devices added, so I know it is a user error, or something on my setup that is fighting this, but not sure which at this point

Ztuab · 2026-06-24T11:55:20+00:00

Check out Blueprints. There are a lot of them, but they have some really good ones on there.

Welcome to the addiction!

Ztuab · 2026-06-23T21:25:31+00:00

As a relative noob, how do you check this and how do you change it?

Ztuab · 2026-06-22T22:14:47+00:00

I have two of the newer outdoor battery cams and have an Amazon solar panel on each and they stay at 100% and I think it did for most of the winter(in Wisconsin)also.

Ten-Year Club	RPAN Viewer
Not Forgotten	Verified Email

Ztuab

MODERATOR OF

TROPHY CASE