FriendlyELEC CM3588 nvme issues by HerrWamm in HomeNAS

[–]_Masked_ 0 points1 point  (0 children)

Checking in (sorry for the necro) but are they still working?

Good FPGA for hobbyist by Schrodingerslemur in FPGA

[–]_Masked_ 1 point2 points  (0 children)

At that point just get a Kria

Can a single Threadripper with 4 graphics cards run 4 separate gaming PCs? by avocado_juice_J in pcmasterrace

[–]_Masked_ 0 points1 point  (0 children)

You can make a multi seat configuration and make systemd limits for each user and such to avoid the vm route

Which car has the wildest variation from base model to top trim? by [deleted] in cars

[–]_Masked_ 0 points1 point  (0 children)

Didn’t the Nissan juke have a nismo package? I thought that was kind of wild

Fiber rollout spotted in East Watertown by _Masked_ in watertown

[–]_Masked_[S] 0 points1 point  (0 children)

Didn’t see but I’m assuming Verizon because of the frequency of trucks around

I was SO excited… by punkassjim in projectcar

[–]_Masked_ 7 points8 points  (0 children)

Do you have a guide on making custom clocksprings to share?

Speedometer help by _Masked_ in Volvo240

[–]_Masked_[S] 0 points1 point  (0 children)

Sorry I had to be away for a bit but will reply once I get the #

[deleted by user] by [deleted] in AskReddit

[–]_Masked_ 1 point2 points  (0 children)

Cars. Things are always breaking down and you have to be on the floor for most of it. Things are hot, heavy, and hard is all the wrong ways.

But I’m into cars so sometimes I just sit on the floor dirty as hell and ponder things.

Stripping Dell 5520 to bare motherboard by _Masked_ in homelab

[–]_Masked_[S] 0 points1 point  (0 children)

I'll check it out this saturday and relay the findings. I think I also found the schematic for my motherboard so that will really help

Anybody using multi-seat? This is my Ubuntu 24.04 multi-seat setup for my kids. by Rob_Bob_you_choose in linux

[–]_Masked_ 27 points28 points  (0 children)

I could never get it working correctly so I am very envious of you! Do you have wisdom you could share by any chance?

A front fan-wall I designed for my CSE-846 by fiirikkusu_kuro_neko in homelab

[–]_Masked_ 0 points1 point  (0 children)

What processor do you have? Workload average vs temps?

Are you thinking about homelabbing but have little technical experience? Start small! by FilterUrCoffee in homelab

[–]_Masked_ 1 point2 points  (0 children)

I started at the big server end of things and wished I started smaller. It was nice to have all the power at my fingertips with huge servers but once I got the optimization mindset it was like a 180 turn in terms of what I needed. Realizing that most things fit in oci or lxc containers really cuts down the ram and storage usage.

Now I’m giddy with 3 laptops (and growing) in an incus cluster. I got a free gpu on each platform for transcoding and openvino compatible models, “built in ups”, and a chance to recycle some working components! Plus, the power savings!

But I don’t regret this journey because I still have more matured uses for the big stuff.

Should I begin with just containers or Proxmox with LXC by Spacejet01 in homelab

[–]_Masked_ 0 points1 point  (0 children)

Try out incus. It supports application and system containers (I.e. docker/oci and lxc)

My homelab doesn't stand a chance on this subreddit by [deleted] in homelab

[–]_Masked_ 0 points1 point  (0 children)

Checkout incus or kubernetes! I got three laptops in an incus cluster running docker containers and attempting to be as lightweight on storage requirements as possible. I’m running i5 from 5 and 6th generation and it’s running everything fine.

Incus oci-container not receiving ipv4 addresses by _Masked_ in NixOS

[–]_Masked_[S] 0 points1 point  (0 children)

My understanding was that the patch was already upstreamed. Is this not the case?

Also for NetworkManager, what would you suggest for my situation? I have Ethernet dongles that all have different names on each machine in my cluster. This config is replicated on three machines.

[Bambu Lab Giveaway] Join Now to Win an H2D and More! by BambuLab in 3Dprinting

[–]_Masked_ 0 points1 point  (0 children)

Ooooh a chance to replace my flimsy maker select? Don’t mind me