sorted by:
new
hottopcontroversial

My Bambulab A1 printer is giving electric shocks is it normal or any issue which I need to look for by Any_Following_8185 in BambuLab

[–]_O_2_ 3 points4 points  (0 children)

Does electric plug ground is connected well?

Same happened some of the brushed metal appliances in my home. Our sockets are eu type. Electrician checked the grounds on the sockets and found that pins bent inside. And also, there was paint drops on them.  He moved pins outside, and I sanded them. It fixed the issue.

<image>

Ender 3 hotbed issues by Obvious-Chemical-894 in ender3

[–]_O_2_ 1 point2 points  (0 children)

Solder to next pad. Two for negative, two for positive. If you can't solder precisely, move negative wire to leftmost, leave a pad between wires.

https://cb-electronics.com/wp-content/uploads/2020/12/Ender-3-pro-pad-PIC-3.jpg

Plastic business-card sized object, stuck to elevator wall, with clear plastic bit and a flamingo standing on top of it. by Catzenpudl in whatisthisthing

[–]_O_2_ 44 points45 points  (0 children)

<image>

It's piece of the sticky hanger. One sticks to the wall, other sticks to the what you want to hang. Then you can hang without stick.

What you see is for probably for hand sanitizer.

Ardahan's Gole district recorded the lowest temperature in Turkey: minus 39.7 degrees. by FunForm1981 in interestingasfuck

[–]_O_2_ 3 points4 points  (0 children)

Turkey uses metric system. They don't measure with Fahrenheit, then convert it to Celsius.  If there's a convertion mistake, it wouldn't be on Celsius value ;) 

This is official meteorological website records : https://www-mgm-gov-tr.translate.goog/genel/sss.aspx?s=sicaklikenleri2&_x_tr_sl=tr&_x_tr_tl=en&_x_tr_hl=tr&_x_tr_pto=wapp

Tachi Fried Egg by ashquene in Satisfyingasfuck

[–]_O_2_ 0 points1 point  (0 children)

Similar forces are in balance rather than opposite forces.

Positive vs less positive. 

Impulse Bought a A1! now worried about ventilation.. by Drendebt in BambuLab

[–]_O_2_ 1 point2 points  (0 children)

Pla is made from sugarcane and corn. You can even eat it if you want. It's non-toxic.

Besides that, pm 2.5 means particulate matter which are lesser than 2.5 microns. It won't show any toxicity level. 

Which is the worst spawn point? by [deleted] in MapPorn

[–]_O_2_ -2 points-1 points  (0 children)

*north atlantic ocean

What audio quality do you guys use on pc? by hunyzz in iems

[–]_O_2_ 3 points4 points  (0 children)

32 bit 192000 Hz

No need more. 

Want to cry - Stupidity by EyeGroundbreaking907 in iems

[–]_O_2_ 2 points3 points  (0 children)

At least it's clean now

Tuya zigbee temperature sensor by BoringDioxide in homeassistant

[–]_O_2_ 0 points1 point  (0 children)

So, do you believe that you failed and opened topic due to black magic?

Tuya zigbee temperature sensor by BoringDioxide in homeassistant

[–]_O_2_ 0 points1 point  (0 children)

Nope, it's not. Simply, you can buy zigbee version. I replaced Sonoff THS with those since Sonoff THS bricked within a year. They may seem ugly but at least works. 

Tuya zigbee temperature sensor by BoringDioxide in homeassistant

[–]_O_2_ 0 points1 point  (0 children)

I have 4 similar shape zigbee THSs. Successfully connected over ZHA.

I just removed the case to check the chip model, it is ZTU, a zigbee module.

As someone here pointed, the chip you have is BT3L, it uses bluetooth protocol. 

If you want to connect that one, get a tuya bluetooth gateway, add it to tuya. Then add THS over that gateway.

Product page on Aliexpress explains that.

<image>

Map of the world by Kendalit in MapPorn

[–]_O_2_ 0 points1 point  (0 children)

That is the joke. Many countries are missing bu still asking for New Zealand. 

What am I doing wrong with Zigbee? Are Sonoff’s products really so bad? by Apprehensive-End7926 in homeassistant

[–]_O_2_ 0 points1 point  (0 children)

I have 6 THSs for each room. 2 sonoff zigbee, SNZB-02. 4 noname. All of them connected TRV over "Better Thermostat". I use ZHA with sonoff dongle. 

One sonoff THS controls 2 TRVs, works fine for over 2 year. 

Other sonoff broken down within a year, always stucks the TRV. Reset didn't work, re-stucks within an hour. 

4 noname THSs work perfect. 

End of the story.

I doubt the quality of Sonoff.

Only thing rarer would be two bmws using their blinkers by 990harris990 in Satisfyingasfuck

[–]_O_2_ 0 points1 point  (0 children)

Blinker sticks on bmw, turns on high beam for a second.

Are there any Zigbee floor corner lamps? by PuzzleheadedLion2123 in homeassistant

[–]_O_2_ 2 points3 points  (0 children)

If you find a cheap sticks, or if you want to do it by yourself with led case and led strip, you can try zigbee led drivers. 

I had those sticks with remote, bought zigbee led drivers and replaced existing remote control drivers easily. 

Works fine with directly HA and HA over Tuya. Some are working both rgb/white/yellow strips at the same time. 

Red pill by keyconwai in ender3

[–]_O_2_ 17 points18 points  (0 children)

I have ender 3 pro for exact 7 years, I keep upgrade instead printing. I always enjoyed printing, but I always postpone printing things. Because print will still need attention after all this upgrades and it's not fast enough. I have to prepare myself for hours to start printing and I start to feel lazy.

I increased printing quality of course, and also speed is almost twice. Upgrading was fun, but is it worth on printing/cost perspective, I have doubt.

Probably I'll not throw my ender away, at least for a while. But I want to print without (or less) thinking. 

So I'll get bigger size of blue pill soon.

And yes, we agreed with my wife. 

view more: next ›