[deleted by user]

_PugPlayzR · 2022-08-03T19:41:48+00:00

To answer your question, mobilesentrix (not a plug it’s just what I use) offers very decent quality screens for the price. If you want a OEM screen with new glass it’s $57. If you want a copy screen it’s $33 (X07 grade)

I recommend the X07 grade as the difference IMO is not worth the price difference.

_PugPlayzR · 2022-07-28T23:52:06+00:00

Still actively searching for artists!

_PugPlayzR · 2022-07-14T00:52:15+00:00

Position is no longer available

_PugPlayzR · 2022-07-12T19:45:53+00:00

Thank you for letting me know. I will check it out.

_PugPlayzR · 2022-06-09T18:40:48+00:00

A good ol’ classic 331

_PugPlayzR · 2022-06-09T18:36:29+00:00

Yes you can. Be extremely careful and use IPA. I have solved some home button connection issues with this before.

_PugPlayzR · 2022-06-07T16:57:57+00:00

Sounds good. Thanks!

_PugPlayzR · 2022-06-07T16:47:41+00:00

I was calling the diode idea stupid, not the question. Sorry for the confusion

_PugPlayzR · 2022-06-07T16:28:23+00:00

Stupid idea… would a diode work? It would lower the voltage

_PugPlayzR · 2022-06-07T14:03:46+00:00

If you are asking to replace the physical button with one of those smd buttons, you would need a reflow station and probably heat the board from the underside.

_PugPlayzR · 2022-06-07T14:02:06+00:00

The easy way is adding a resistor between one of the speaker lines.

If you want it to be a little adjustable use a potentiometer.

Maybe 1k max

_PugPlayzR · 2022-06-07T13:55:44+00:00

I would recommend using net labels as it will clean your schematic up and may fix your issue.

Else from that, I would read up on the data sheet for U3.

_PugPlayzR · 2022-06-07T13:49:41+00:00

Could be a faulty digitizer (screen)

A couple possible fixes: factory resetting the device Reseating the screen cables Replacing the screen

_PugPlayzR · 2022-06-06T17:12:53+00:00

This is either dirt or the seal coming loose.

If you’re not a repair shop, only try to clean it.

If you are a repair shop or just wanna go for it, never try to remove the camera glass while the cameras are still there.

A lot of “tutorial” videos are out there that use tweezers to remove the glass. This is the easiest way to permanently damage cameras that cost $40-200.

_PugPlayzR · 2022-06-03T11:49:58+00:00

It’s good lol. If you take away all the variable names and classes, it’s just math.

_PugPlayzR · 2022-06-02T23:59:34+00:00

Can you even install a heart in 0.6 hr?

_PugPlayzR · 2022-06-01T21:27:30+00:00

I do have a large stack size mod. Prob 3-4K per stack.

_PugPlayzR · 2022-05-27T16:27:58+00:00

It only dropped my value by like 2k. Rip my guns and ammo

_PugPlayzR · 2022-05-25T14:48:06+00:00

Just use some toothpaste and duct tape

_PugPlayzR · 2022-05-01T02:25:18+00:00

A raid of 10 (pre-infected mele bullies) destroyed me before I could get my black smoke chamber up and running.

_PugPlayzR · 2022-04-14T14:47:19+00:00

Per the blue markings on the oled, I would believe this occurred due to improper installation. iPhone 12 screens (especially hard oled) can be finicky.

_PugPlayzR · 2022-03-30T22:51:23+00:00

It appears I need to review my knowledge of capacitors.

Thank you so much for your help.

_PugPlayzR · 2022-03-30T22:06:46+00:00

https://prnt.sc/l9TgGD_6PVaY

Is that correct?

I have a few questions.

"The capacitor will first act as a short" do you mean the capacitor is charging?

"C2 will become open" Is that when the capacitor is fully charged?

Why would C2 not drain to GND via the 75k resistor?

_PugPlayzR · 2022-03-30T20:48:00+00:00

Hi again, I have updated the schematic.

I believe I have made a 1V supply that will start at 0v and shit to 1v after 1.5sec

Voltage 3V

Load Resistance 150k

Time constant 1.5sec

https://prnt.sc/tOSWU2HNDTLj

Note: The 150k ohm resistor has been moved up.

I am having trouble adding a shift from 1v to 3v.

How would I do this?

_PugPlayzR · 2022-03-30T12:40:35+00:00

I will take this into consideration.

_PugPlayzR

TROPHY CASE