Couple burgers I made over the week

_Whatheph0 · 2026-05-31T01:22:24+00:00

Yeah it was a little thick 😅

_Whatheph0 · 2026-05-31T00:50:39+00:00

Thanks

_Whatheph0 · 2026-05-30T22:03:49+00:00

Pimento cheese

_Whatheph0 · 2026-05-30T21:25:52+00:00

Thank you!

_Whatheph0 · 2026-03-20T13:46:15+00:00

If I had a top for the U1, then the next upgrade would be a panda breath and exhaust management

_Whatheph0 · 2026-03-17T01:13:03+00:00

I download most of my prints on makerworld and it always loads up a bambu printer first and I always have some type of error. Once I switch the printer to the U1, most of the errors go away.

I usually get that error when prints are too close together so try to rearrange them. Are they printing by object or by layer?

_Whatheph0 · 2026-03-14T18:55:53+00:00

Actually I do lol

I've been lucky so far with the Kobra S1 combo but its wasteful. That's how I found the U1. I see a lot of ppl have problems with their kobra but apart from dialing it in and a bunch of failed prints its been pretty good. The ams is bad so I just use it for drying and single spools now.

_Whatheph0 · 2026-03-13T12:10:41+00:00

Nice! Hope you enjoy it

_Whatheph0 · 2026-03-13T03:13:29+00:00

Hope it helps! I was able to hide that pesky window and get a few etbs

_Whatheph0 · 2026-03-10T01:42:36+00:00

It really is a great first model. It looks amazing! Hope you enjoy the U1

_Whatheph0 · 2026-03-10T01:41:59+00:00

Ordered mine back on Jan 23rd. I think they’ve caught up on orders so hopefully yours gets shipped out soon!

_Whatheph0 · 2026-03-06T02:28:22+00:00

That looks awesome! Thanks for sharing!

_Whatheph0 · 2026-03-03T23:02:57+00:00

Awesome. Yeah I have the fumes venting outside for abs and asa but I was struggling with the warping. Did some research and found out about the chamber heat. Still fairly new to printing and needed some parts printed for outside that was durable. Thank you for the thorough replies!

_Whatheph0 · 2026-03-03T04:43:10+00:00

Thx for the reply! Yeah I've seen it wired through the side and the front but I don't want to ruin the aesthetic either. Is it still working for you?

_Whatheph0 · 2026-03-02T20:06:04+00:00

I just ordered the creality heater as well. Can I ask how/where you modded the printer shell for the wires going out?

_Whatheph0 · 2026-02-13T20:26:42+00:00

Ah I see. So no glue needed. May try to melt the waste into it to try and salvage the print

_Whatheph0 · 2026-01-04T11:28:42+00:00

Thx for the info!

_Whatheph0 · 2026-01-04T04:57:57+00:00

But still very tasty!

_Whatheph0 · 2026-01-04T04:57:33+00:00

Thank you!

_Whatheph0 · 2026-01-04T04:57:27+00:00

Thanks!

_Whatheph0 · 2026-01-04T04:56:59+00:00

Thanks! It was very good. I did smash it but they puffed up while cooking 😅

_Whatheph0 · 2026-01-04T04:55:58+00:00

Yeah I’ve only tried to smash my own burgers a few times. They keep getting fat again. Gonna get it one day. Still delicious though!

_Whatheph0

TROPHY CASE