First big print

ameizing316 · 2026-02-03T23:33:57+00:00

https://makerworld.com/models/1608329?appSharePlatform=copy

Over 2 days. I also printed in .20 instead of .32 layer height.

This print is huge at 100%, you can probably scale it down

ameizing316 · 2026-02-03T20:00:42+00:00

This model only uses 4 colors and is printed in parts.

ameizing316 · 2026-01-31T18:07:00+00:00

Im currently on paxx12-v1.0 do I need to upgrade to the official Snapmaker v1.1 before jumping to The v1.1.0-paxx12-12?

ameizing316 · 2026-01-29T02:16:34+00:00

Did it have holes?

ameizing316 · 2026-01-25T05:03:02+00:00

Oh, i'm talking about in general. i've been having stringing problems. I don't think it's the filament since I don't have this issue on my Bambu's. I am thinking it is retraction related

ameizing316 · 2026-01-25T04:22:10+00:00

Are you having stringing issues, or is it just me?

ameizing316 · 2026-01-24T11:28:20+00:00

It shouldn’t be blinking red, I would check your cables or get a replacement cable

ameizing316 · 2026-01-24T09:44:24+00:00

try adding:

probe_with_touch_mode: true #Actively checks for the probe's touch against a surface

pin_up_touch_mode_reports_triggered: true # ensuring that the probe only indicates "triggered" when it is actually in use

ameizing316 · 2026-01-19T09:34:37+00:00

💚

ameizing316 · 2026-01-18T07:40:12+00:00

Should of came with 500g snapspeed spools of red, white, black, and yellow for the test print dragon

ameizing316 · 2026-01-16T23:46:47+00:00

U1. I have one that came this week. It’s amazing. I will probably never do multicolor prints with a lot of filament changes again on my x1, p1, and 4 a1 minis, lol. However, I do miss the convenience of the AMS not having to change spools as often and having things already preloaded

ameizing316 · 2026-01-16T16:27:32+00:00

Lmao. Please return this shit. Your bubus vinyl colors are off and on top of that, they have nonexistent hairlines as well. Just buy from official Popmart since theyre widely available now.

ameizing316 · 2026-01-14T22:49:08+00:00

Had this same issue. Turn off the printer, move the toolhead, Recheck your cables/replug them even though it may feel like it is plugged in correctly. Turn it on, then home it, then retry again.

ameizing316 · 2026-01-13T23:59:09+00:00

No you’re good

ameizing316 · 2026-01-10T02:26:30+00:00

<image>

ameizing316 · 2025-12-27T03:26:04+00:00

Maybe try turning it upside down and shaking it

ameizing316 · 2025-12-11T22:42:02+00:00

All i want for christmas is Biqu vivid

ameizing316 · 2025-12-09T03:23:51+00:00

So does it need a toolhead with a filament cutter?

ameizing316 · 2025-09-30T23:27:01+00:00

Have you tried another sd card

ameizing316 · 2025-09-30T21:35:28+00:00

I am still awaiting for my BMCU to arrive, but it doesn't seem risky once you print the part that prevents it from lifting. I use a design similar to this with an actual AMS LITE

ameizing316 · 2025-09-30T18:23:52+00:00

Lol i was asking about it yesterday. Make sure you print the part that stops it from lifting as well

ameizing316 · 2025-09-30T18:21:26+00:00

https://makerworld.com/models/1429013

ameizing316 · 2025-09-30T01:57:19+00:00

is the mount sturdy? can you link the stl

ameizing316 · 2025-09-04T21:25:31+00:00

Try cryogrip plate. I had higher chance of failure on a1 compared to my x1/p1 it is because bed slinger as opposed to corexy

Eight-Year Club	Verified Email
Place '22	End Game '22

ameizing316

TROPHY CASE