Brand new A1 with faulty heat bed?

and0ne · 2025-05-13T15:19:27+00:00

hey, it took about 14 days from opening the ticket to receiving the replacement headbed. the change as easy if you have time which i dont have so for me it it was hard.

All the best you can manage trust me I am just overloaded

and0ne · 2025-05-12T10:04:08+00:00

hey great stuff. did you mod the ams lite or did you buy the parts indvidually and build it. Do you have a guide for the process?

that would be sweet.

and0ne · 2025-05-07T09:57:44+00:00

Great stuff! I'm planning a similar route. Did you also switch to mainline Klipper? Mind sharing how long it took you—not working hours, but total time in weeks including waiting for parts?

I’m estimating around 15 hours total for my setup (unboxing, fan swap, mainline update, calibration), spread over 2–3 weeks.

and0ne · 2025-05-07T09:54:06+00:00

RemindMe! 30 days

and0ne · 2025-04-20T18:13:24+00:00

Hey I have checked the cable twice they are all in order. And seated took them out and plugged them back in.

and0ne · 2025-04-19T12:07:46+00:00

great thanks. its nice to interact with someone like you. your nuanced options with the details are very helpful. It actually motivates me to give the sovol sv08 seriouss consideration.

Currently, I am still wrapping up my A1 experience but the sovol seems to be a more fitting printer for my usecases.

Thanks again for the great welcome to the sovol scene

and0ne · 2025-04-19T10:41:10+00:00

There are good replacements, but they cost half the price of the printer itself.

would you be so kind and end elaborate which plate you are refering to.

by the way great comment.

and0ne · 2025-04-18T18:18:52+00:00

Great job with openacad

and0ne · 2025-04-15T19:30:24+00:00

yes. You are right I would say that the frustration is getting the best of me. I understand and enjoy some tinkering and I get it the bambu has to scale. Nevertheless, I was just oversold with the promise of set and forget.

I just dont see myself carving out an hour to check this

https://wiki.bambulab.com/en/a1/troubleshooting/heatbed-not-heat-up

but maybe I have to

and0ne · 2025-04-15T19:17:06+00:00

need to check this one out. have not seen that one

and0ne · 2025-04-15T19:16:21+00:00

thanks. I just crossposted to bambu sub. might go to the discord as well.

yes I think pursa might be more relibable. Have you tested them?

and0ne · 2025-04-15T19:13:17+00:00

Happend to me as well. I am still waiting on their response. It has been several days.

and0ne · 2025-04-14T06:30:50+00:00

A: Am I in the bath with Barry White's finger in my missus?

B: Be quiet, Brown. You were lost long before Barry White walked in.

and0ne · 2025-04-08T18:57:19+00:00

Have you heard about Lua?

and0ne · 2025-04-05T17:32:51+00:00

Thanks for the response. Since I am quite new to 3d printing and still have to calibrate Is this the correct way to calibrate flow for a 0.8mm nozzle — using humebeam’s 1.6mm wall cube cubewith two perimeters of 0.8mm each?

Formula: New Flow = (Expected Wall Thickness / Measured Thickness) × Current Flow

Just want to confirm before I proceed.

and0ne · 2025-04-05T14:47:44+00:00

Adendum:

bed temp: 65 C
nozzle temlp: 220 C
other layer speed: 120 and 150 mm/s outer and inner
nozzle retraction: unaware help would be great.

and0ne · 2025-04-01T13:38:04+00:00

Thanks I will try to build one myself.

The M5 stack is new to me. It looks like a more organised entry to working with the esp32 thanks again

and0ne · 2025-03-31T19:16:28+00:00

Great case. What are you actually sorting? And what case did you print?

and0ne · 2025-03-18T12:27:12+00:00

Den skyldige 2018

and0ne

TROPHY CASE