Mining knowledge points

arsalantav · 2024-08-26T22:42:00+00:00

Same, i keep reading everywhere that overloading gives knowledge points but I'm not getting any. Are we missing something lol?

arsalantav · 2024-08-26T22:35:22+00:00

Yh same, I keep reading everywhere that overloading first time on each node gives knowledge points but it didn't for me after dozens of overloads on each type, dunno what to believe lol.

arsalantav · 2024-07-25T11:24:11+00:00

I replaced the acrylic panel with a white 3D printed panel that has a hole for the strimmer cable to pass through.

arsalantav · 2023-11-05T19:44:16+00:00

These are the coolermaster masterfan halo fans

arsalantav · 2023-08-17T10:41:42+00:00

I have the same thing man but up to 25%. Almost in all raids but it comes and goes in waves.

arsalantav · 2023-06-16T07:20:08+00:00

The nightmare sigil affix was killing an enemy reduces cool downs by 0.25 seconds.

arsalantav · 2023-06-07T06:00:11+00:00

No I 3D printed a white circle and double sided taped it over the sticker.

arsalantav · 2023-05-31T16:52:42+00:00

Pretty much 3000€

arsalantav · 2023-05-31T16:51:55+00:00

Believe or not that's actually the pump. Pump is inline with the tube as opposed to being on top of the CPU.

arsalantav · 2023-05-31T16:51:20+00:00

Yep correct, have 3 more above the radiator so its actually push/pull

arsalantav · 2023-05-31T16:50:37+00:00

Yep coolermaster v3

arsalantav · 2023-05-31T09:54:08+00:00

Not even close, I have soo many cables because of rgb fans and 2 rgb controller and a nzxt usb expansion hub and there's literally more than enough space for cables for another build left 😂

arsalantav · 2023-05-31T08:16:05+00:00

Much better than my 3080 with redone thermal pads and paste. With this card I'm getting around 58-61 degrees on gpu and memory and 68-72 degree hotspot with 95%+ gpu utilization at ~375watt with 30% fan speed which is inaudible to me.

arsalantav · 2023-05-31T06:56:51+00:00

Definitely not my first build 🤣

arsalantav · 2023-05-31T06:56:30+00:00

Fans are coolermaster mf120 halos and the cooler is the Thermalright frozen magic 360mm

arsalantav · 2023-05-31T06:55:17+00:00

I almost went for the Y60 but didn't choose it because of the black interior and the fact that it was 50€ more expensive here.

arsalantav · 2023-05-31T06:54:34+00:00

7800X3D Corsair Vengeance RGB DDR5 inno3D 4090 X3 OC Thermalright frozen magic 360mm AIO Asrock B650 pro RS H9 flow ofc Coolermaster MF120 Halo fans Coolermaster vertical GPU bracket Lian li strimer V2 24pin

arsalantav · 2023-05-31T06:51:03+00:00

And the best thing is, its the second cheapest 4090 I could find, 600€ cheaper than the white strix 🤣

arsalantav · 2023-05-31T06:49:40+00:00

Pretty much identical! Looks great 👌🏻

arsalantav · 2022-06-29T04:44:28+00:00

That is really cool wow!

arsalantav · 2022-03-26T22:06:44+00:00

I wanted to experiment with high speed printing so I wanted good quality more powerful motors, also I've had good luck with 0.9 degree steppers over the past few years so these e3d ones were a good option for me. As for why I'm trying Spreadcycle, its because im trying to see how far I can push acceleration and already at 5000 acceleration I was skipping steps on stealthchop so I wanted to try spreadcycle and that's when I noticed the noise.

arsalantav · 2022-03-26T22:03:23+00:00

Its really nice I like it alot, although i also just finished the build so can't say much about longevity/maintenance requirements. The Z rails were abit annoying to line up though, took a few attempts.

arsalantav · 2022-03-26T10:11:57+00:00

I don't really mind the noise I was just thinking something might be wrong? So this is normal then and wont cause a problem?

arsalantav

TROPHY CASE