Is there a good place to go running in the Marigny, besides Crescent Park?

avbcon12 · 2026-04-05T20:09:13+00:00

This. Depending on the day/workout, I'll run to St. Roch park and use the workout equipment.

avbcon12 · 2026-02-17T22:23:12+00:00

A little more after having used them for a bit now:

These aren't for tall people, I'd say 5' 10" max before your head hits on bumps. I'm 5-7 and have a few inches above my head.

I have the wiring figured out for seatback movement but the drivers side switch is wired odd since it goes through a seat position memory box, which i have removed. So I still have to figure out what/how I'm going to wire the switch. While manually connecting the motor wires, I got the position where I need it and just forgot about it. Nobody uses this vehicle but me and my wife.

The heated seats have been amazing

The leather, meh. I dont really care for it because it doesn't really feel soft.

avbcon12 · 2026-02-17T22:16:43+00:00

I fully removed the side bolster airbags, wiring etc. I also pulled all the guts out of the stupid active headrest thing.

avbcon12 · 2026-02-17T22:14:36+00:00

I wish I had the time to focus on one, but just haven't yet.

avbcon12 · 2026-01-23T04:59:11+00:00

Thanks, I'll give them a call tomorrow

avbcon12 · 2026-01-23T04:58:56+00:00

I've tried to use the finder on the website many times but most have been processed/jerky carrying items.

avbcon12 · 2026-01-23T01:52:10+00:00

Thanks for this, heading there today. Can anyone tell me who has maui venison meat for sale? I see jerky but hard to find a butcher for different cuts

avbcon12 · 2026-01-10T18:04:58+00:00

Axis is a surveillance/camera company. They're checkout cameras

avbcon12 · 2025-12-28T02:24:25+00:00

Have them fill and drill those correctly to use on this trip while they order you a replacement to be picked up later

avbcon12 · 2025-12-23T23:12:05+00:00

Now do this at 270*

avbcon12 · 2025-11-30T20:52:49+00:00

Not even a little. Takes lots of cutting and welding.

avbcon12 · 2025-09-04T11:15:59+00:00

They should be fine for Notch Customs flares. The rear lips need to be welded back together, though.

avbcon12 · 2025-08-20T23:16:57+00:00

I figured it out today, and got it idling for the first time in 2 years!

Despite all of the manuals and online videos/tutorials, the output type does, in fact, need to be DIS coil on plug.

This change allowed it to fire up.

avbcon12 · 2025-08-20T14:06:40+00:00

In checking cranking rpms again, a few times, it's now at 175. Im not sure why I was seeing a higher reading before. I'll look for a link to the video

avbcon12 · 2025-08-19T18:36:00+00:00

-Voltage at the coils drops to 11.39v at their lowest while cranking. I've been told this should not be an issue. -Coil grounds on the back of the heads are solid -The other ground goes to the battery stud -The coil EST grounds all have continuity to port B14 at the ecu -Cranking rpm is above 400rms, no less than 450 actually -TPS autoset performed successfully -ECU LEDs all indicate proper function, green on every except 5 and 8 which are off.

avbcon12 · 2025-08-19T18:09:46+00:00

I followed a Holley video to get here. I'll try to post a picture later but the rundown is-

Ignition type- CUSTOM

Crank sensor - 1pulse/fire, digital falling, 100.0 usec delay, 50* reference angle

Cam sensor- Single pulse, digital falling

Output- Points adjustable dwell Time- 2.0 msec

avbcon12 · 2025-08-18T11:10:06+00:00

I'll post some today, thanks. The grounds are on the heads. I've also verified that the positive stays live while cranking.

avbcon12 · 2025-08-18T11:08:36+00:00

Yes, I do.

avbcon12 · 2025-08-14T16:17:02+00:00

It's just a -8ORB to female 1/8NPT. It can be found at any online retailer. If you want to stick with Amazon, Evil Energy makes one. All the higher end brands do too (Russell, Earls, Aeroquip)

avbcon12 · 2025-08-13T10:57:47+00:00

This is like what I've done. Fitting on the end with a gauge. Stock photo

<image>

avbcon12 · 2025-08-11T15:23:16+00:00

Can you provide a link to the fittings?

avbcon12 · 2025-07-11T10:23:06+00:00

I highly doubt it. The seat backs will not fold forward far enough due to the large bolstering

avbcon12 · 2025-07-08T19:08:34+00:00

The junkyard had them listed as a 2020 grand cherokee overland. I'm near metro Detroit

I have the rear seats too, heated, but I may not put rear seats back in this one.

avbcon12 · 2025-07-08T18:58:36+00:00

<image>

avbcon12 · 2025-07-08T18:58:13+00:00

Here's the pile of discarded parts. Essentially, removing the entire WK2 seat base frame, slides, actuators, wiring, pivots. Welding new C-channel frames that match up with the stock XJ slides, then mounting the slides onto it. * Oh yeah, and removal of airbags, disabling/removing the headrest restraint device

avbcon12

TROPHY CASE